- 您現在的位置：買賣IC網 > PDF目錄369882 > LX8386-33CDLT THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS PDF資料下載
參數資料
| 型號： | LX8386-33CDLT |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| 中文描述： | 三端固定電壓調節器 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 143K |
| 代理商： | LX8386-33CDLT |
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 7
Copyright
2000
Rev. 2.1d, 2001-03-15
W
M
.
LX8384x-xx
5A Low Dropout Positive Regulators
P
RODUCTION
A M I C R O S E M I C O M P A N Y
LOAD REGULATION (continued)
Even when the circuit is configured optimally, parasitic
resistance can be a significant source of error. A 100 mil. wide
PC trace built from 1 oz. copper-clad circuit board material has a
parasitic resistance of about 5 milliohms per inch of its length at
room temperature. If a 3-terminal regulator used to supply 2.50
volts is connected by 2 inches of this trace to a load which draws
5 amps of current, a 50 millivolt drop will appear between the
regulator and the load. Even when the regulator output voltage is
precisely 2.50 volts, the load will only see 2.45 volts, which is a
2% error. It is important to keep the connection between the
regulator output pin and the load as short as possible, and to use
wide traces or heavy-gauge wire.
The minimum specified output capacitance for the regulator
should be located near the regulator package. If several capacitors
are used in parallel to construct the power system output
capacitance, any capacitors beyond the minimum needed to meet
the specified requirements of the regulator should be located near
the sections of the load that require rapidly-changing amounts of
current. Placing capacitors near the sources of load transients will
help ensure that power system transient response is not impaired
by the effects of trace impedance.
To maintain good load regulation, wide traces should be used
on the input side of the regulator, especially between the input
capacitors and the regulator. Input capacitor ESR must be small
enough that the voltage at the input pin does not drop below
V
IN(MIN)
during transients.
V
V
+
=
X)
DROPOUT(MA
V
OUT
where: V
IN(MIN)
V
OUT
V
DROPOUT(MAX)
the specified dropout voltage for the
installed regulator.
THERMAL CONSIDERATIONS
The LX8384/84A/84B regulators have internal power and
thermal limiting circuitry designed to protect each device under
overload conditions. For continuous normal load conditions,
however, maximum junction temperature ratings must not be
exceeded. It is important to give careful consideration to all
sources of thermal resistance from junction to ambient. This
includes junction to case, case to heat sink interface, and heat
sink thermal resistance itself.
Junction-to-case thermal resistance is specified from the IC
junction to the back surface of the case directly opposite the die.
This is the lowest resistance path for heat flow. Proper mounting
is required to ensure the best possible thermal flow from this area
of the package to the heat sink. Thermal compound at the case to
heat sink interface is strongly recommended. If the case of the
device must be electrically isolated, a thermally conductive
spacer can be used, as long as its added contribution to thermal
resistance is considered. Note that the case of all devices in this
series is electrically connected to the output.
the lowest allowable instantaneous
voltage at the input pin.
the designed output voltage for the
power supply system.
Example
Given:
Find:
Solution: The junction temperature is:
T
=
P
V
IN
V
OUT
=
I
OUT
T
A
R
300 ft/min airflow available
=
5V
2.8V
5.0A
50°C
2.7°C/W for TO-220
=
=
=
Proper Heat Sink to keep IC’s junction temperature
below 125°C.**
A
J
T
)
R
R
(R
+
+
+
D
where:
P
D
Dissipated power.
Thermal resistance from the junction to
the mounting tab of the package.
Thermal resistance through the
interface between the IC and the
surface on which it is mounted.
(1.0°C/W at 6 in-lbs mounting screw
torque).
Thermal resistance from the mounting
surface to ambient (thermal resistance
of the heat sink).
Heat Sink Temperature.
T
C
T
S
T
A
R
T
R
R
T
S
T
J
R
θ
JT
R
θ
CS
R
θ
SA
First, find the maximum allowable thermal resistance of the
heat sink:
T
T
R
=
(
)
CS
D
A
J
SA
R
R
P
+
11.0W
5.0A
2.8V
5.0V
(
=
×
=
=
D
D
P
P
)
I
V
(V
OUT
OUT
IN(MAX)
C/W
°
C/W)
°
1.0
C/W
°
(2.7
5.0A
=
1
*
2.8V)
R
(5.0V
C
50
C
125
+
°
°
=
R
Next, select a suitable heat sink. The selected heat sink must
have R
< 3.1°C/W. Thermalloy heatsink 6296B has R
3.0°C/W with 300ft/min air flow.
Finally, verify that junction temperature remains within speci-
fication using the selected heat sink:
1.0
C/W
11W(2.7
=
J
T
=
C
124
C
50
C/W)
°
3.0
C/W
°
°
+
+
°
+
°
=
J
T
** Although the device can operate up to 150°C junction, it is recommended for long
term reliability to keep the junction temperature below 125°C whenever possible.
A
P
P
L
I
C
A
T
I
O
N
S
相關PDF資料 |
PDF描述 |
|---|---|
| LX8386A-00CDL | Positive Adjustable Voltage Regulator |
| LX8386A-00CDLT | Positive Adjustable Voltage Regulator |
| LX8554 | Positive Adjustable Voltage Regulator |
| LX8610-00 | Positive Adjustable Voltage Regulator |
| LX8610-00CST | Low Drop Out Regulator - Positive Adjustable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX8386-33CDT | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:1.5 A LOW DROPOUT POSITIVE REGULATORS |
| LX8386-33CDTT | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Positive Fixed Voltage Regulator |
| LX8386-33CP | 功能描述:IC REG LDO 3.3V 1.5A TO220 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式和可調式 輸出電壓:3.3V，1.25 V ~ 5.7 V 輸入電壓:4.5 V ~ 7 V 電壓 - 壓降（標準）:1.1V @ 1A 穩壓器數量:2 電流 - 輸出:1A 電流 - 限制（最小）:1A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-252-5，DPak（4 引線 + 接片），TO-252AD 供應商設備封裝:PPAK 包裝:管件 其它名稱:497-3576-5 |
| LX8386-33IDD | 功能描述:IC REG LDO 3.3V 1.5A TO263 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式和可調式 輸出電壓:3.3V，1.25 V ~ 5.7 V 輸入電壓:4.5 V ~ 7 V 電壓 - 壓降（標準）:1.1V @ 1A 穩壓器數量:2 電流 - 輸出:1A 電流 - 限制（最小）:1A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-252-5，DPak（4 引線 + 接片），TO-252AD 供應商設備封裝:PPAK 包裝:管件 其它名稱:497-3576-5 |
| LX8386-33IDDT | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Positive Fixed Voltage Regulator |
發布緊急采購，3分鐘左右您將得到回復。