- 您現在的位置：買賣IC網 > PDF目錄377789 > LX2207 (Microsemi Corporation) Three Level Lithium Ion Battery Charger PDF資料下載
參數資料
| 型號： | LX2207 |
| 廠商： | Microsemi Corporation |
| 英文描述： | Three Level Lithium Ion Battery Charger |
| 中文描述： | 三級鋰離子電池充電器 |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 400K |
| 代理商： | LX2207 |
LX2207
P
RODUCTION
D
ATA
S
HEET
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
Copyright
2005
Rev. 1.0, 2007-01-03
W
M
.
C
Three Level Lithium Ion Battery Charger
TM
A B S O L U T E M A X I M U M R A T I N G S
Supply Input Voltage (IN, BAT) ...................................................................... -0.3V to 7V
All other pins ............................................................................................-0.3V to V
SUPPLY
Battery Charging Current .............................................................................................1.1A
Operating Temperature Range.........................................................................-40 to 150
°
C
Maximum Operating Junction Temperature ..............................................................150
°
C
Storage Temperature Range.........................................................................-65
°
C to 150
°
C
Peak Temp. for Solder Reflow (40 seconds maximum exposure)..................260°C (+0 -5)
Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to
Ground. Currents are positive into, negative out of specified terminal
.
T H E R M A L D A T A
LD
Plastic Micro Leadframe Package 12-Pin
THERMAL RESISTANCE
-
JUNCTION TO
A
MBIENT
,
θ
JA
49
°
C/W
Junction Temperature Calculation: T
J
= T
A
+ (P
D
x
θ
JA
).
The
θ
numbers are guidelines for the thermal performance of the device/pc-board system. All of the
above assume no ambient airflow.
P A C K A G E P I N O U T
1
2
3
4
5
8
9
10
11
12
IN
CMP
STAT
DCOK
BAT
LCP
HCP
TMP
H/L
20%
6
7
GND
SD
LD Package
(Top View)
RoHS / Pb-free 100% matte Tin Lead Finish
F U N C T I O N A L P I N D E S C R I P T I O N
Name
Pin #
Description
BAT
12
Battery – Connect to a single cell Lithium Ion Battery.
CMP
2
Compensation – Connect a series combination of a 1k resistor and a 0.47μF capacitor from CMP to IN.
DCOK
4
Power status logic pin and LED driver – This pin is an open drain output that can sink 20mA of current to
drive an external LED. This pin is low impedance to GND when the Input voltage is high enough to charge
the Battery.
Ground – Connect to the system ground.
GND
7
HCP
10
High Current Programming (and Termination Current Programming) – Connect a resistor to ground to set the
constant current high level. The termination current is set to 1/10 of the High Current Programming Level.
For a value of 19.6k, the High Current is 460mA and the Termination Current is 46mA.
High or Low load select logic input – A logic high selects the constant charge current level set by the HCP pin
resistor and a logic low selects the constant charge current level set by the LCP pin resistor
Input Power – Connect to a wall adapter or a USB power plug.
H/
L
8
IN
1
LCP
9
Low Current Programming – Connect a resistor to ground to set the constant current low level.
For a value of 19.6k, the High Current is 460mA and the 20% current is 92mA.
Shutdown – A logic high places the LX2207 in sleep mode; can also be used for USB suspend.
SD
5
STAT
3
Charging status logic pin and LED driver – This pin can source or sink 10mA of current to drive an external
LED in either output state. This pin is low (current sinking mode) when the battery is in charging mode and
becomes high (current sourcing mode) when the charge cycle is finished. It becomes high impedance when
the input power is removed.
Battery Temperature Monitor – This sense pin determines the battery temperature for charging out of
temperature range lockout and is connected to a resistor network as defined in the Applications section. The
TMP pin is grounded if this function is not used.
20% select logic input – When the low current level is selected by the H/L pin, a logic high on 20% selects the
constant charge current level set by the LCP pin resistor and a logic low selects 20% of this value.
TMP
11
20%
6
P
A
C
K
A
G
E
D
A
T
A
相關PDF資料 |
PDF描述 |
|---|---|
| LX2207ILD | Three Level Lithium Ion Battery Charger |
| LX24T3 | Linear Excimer Lamp |
| LX401 | SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR |
| LX5107CDWT | Terminator |
| LX5107CPWPT | Terminator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX2207 EVAL KIT | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2207_0710 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Three Level Lithium Ion Battery Charger |
| LX2207ILD | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2207ILD-TR | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Three Level Lithium Ion Battery Charger |
| LX2208 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:2 Amp Three Level Lithium Ion Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。