- 您現在的位置：買賣IC網 > PDF目錄377789 > LX2205 (Microsemi Corporation) 1A Li-Ion Battery Charger with Power Source Management PDF資料下載
參數資料
| 型號： | LX2205 |
| 廠商： | Microsemi Corporation |
| 英文描述： | 1A Li-Ion Battery Charger with Power Source Management |
| 中文描述： | 1A條鋰離子電池充電器與電源管理 |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 331K |
| 代理商： | LX2205 |
LX2205
P
RODUCTION
D
ATA
S
HEET
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
Copyright
2007
Rev. 1.0a, 2007-03-02
W
M
.
C
1A Li-Ion Battery Charger with Power Source Management
TM
L
X
2
2
0
5
A B S O L U T E M A X I M U M R A T I N G S
Supply Voltages (MDC, SYS, USB) ................................................................ -0.3V to 7V
Battery Voltage (BAT) ..................................................................................... -0.3V to 6V
All Other Pins.............................................................................................-0.3V to V
SUPPLY
USB Current .............................................................................................................600mA
BAT Discharge Current................................................................................................1.6A
Operating Ambient Temperature Range (T
A
)..............................................-45°C to 125
°
C
Maximum Operating Junction Temperature (T
J
).......................................................150
°
C
Storage Temperature Range.........................................................................-65
°
C to 150
°
C
Lead Temperature (Soldering 10 seconds).................................................................300
°
C
Package Peak Temp. for Solder Reflow (40 seconds maximum exposure)...260°C (+0 -5)
Note: Exceeding these ratings could cause damage to the device. All voltages are with respect
ground. Currents are positive into, negative out of specified terminal
.
to
T H E R M A L D A T A
LQ
Plastic 4 x 4mm 16-Pin
THERMAL RESISTANCE
-
JUNCTION TO
A
MBIENT
,
θ
JA
28
°
C/W*
Junction Temperature Calculation: T
J
= T
A
+ (P
D
x
θ
JA
).
*The
θ
JA
numbers are guidelines for the thermal performance of the device/pc-board system. All of the
above assume no ambient airflow. See layout guidelines section for important details.
P A C K A G E P I N O U T
CMP
BAT
SYS
USB
M
S
S
U
CUS
GND
CCP
CTP
D
C
D
T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Connect Bottom
Pad to GND
LQ
P
ACKAGE
(Top View)
RoHS / Pb-free 100% Matte Tin Pin Finish
F U N C T I O N A L P I N D E S C R I P T I O N
Name
Pin
Description
BAT
2
Battery Connection - This pin is wired to the positive terminal of a single cell lithium ion/polymer battery.
CCP
11
Charge Current Programming Pin - A resistor (R
CCP
) is connected between this pin and GND. The constant
charging current is determined by the following relationship: R
CCP
= 50.648 x I
CCL
with R
CCP
in k
and
I
CCP
in amps.
Charge Indicator - This pin is a logic low level when the battery is being charged, provided V
SYS
is
≥
4.4V. It is
capable of driving the series combination of an LED and resistor that is powered from the SYS pin.
CHG
14
CMP
1
Compensation – Connect a 0.1μF capacitor from CMP to SYS.
CTP
12
Charge Termination Programming Pin – A resistor (R
CTP
) is connected between this pin and GND. The
charge termination taper current is determined by the following relationship: R
CTP
=0.7354 x I
TERM
with R
CTP
in k
and
I
TERM
in amps.
USB Current Limit Programming Pin – A resistor (R
CUS
) is connected between this pin and GND. The high
level USB charge current is determined by the following relationship: I
USB
= 1050 / R
CUS
.
Main DC Present – A low level on this logic output indicates that the Main DC power source (typically the wall
adapter) is applied.
Done Indicator - This pin is a logic low level when the battery charge cycle is complete. It is capable of driving
the series combination of an LED and resistor that is powered from the SYS pin.
CUS
9
OK
DC
13
DONE
15
GND
10
Common Ground – Used as chip ground and as a reference for the battery return.
相關PDF資料 |
PDF描述 |
|---|---|
| LX2205ILQ | 1A Li-Ion Battery Charger with Power Source Management |
| LX2206 | Dual Level Lithium Ion Battery Charger |
| LX2206ILD | Dual Level Lithium Ion Battery Charger |
| LX2207 | Three Level Lithium Ion Battery Charger |
| LX2207ILD | Three Level Lithium Ion Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX2205 EVAL KIT | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2205ILQ | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2206 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Dual Level Lithium Ion Battery Charger |
| LX2206 EVAL KIT | 制造商:Microsemi Corporation 功能描述:LINEAR - LITHIUM ION - Bulk |
| LX2206_07 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:TM Dual Level Lithium Ion Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。