- 您現在的位置：買賣IC網 > PDF目錄377788 > LX1992CDU (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) High Efficiency LED Driver PDF資料下載
參數資料
| 型號： | LX1992CDU |
| 廠商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | High Efficiency LED Driver |
| 中文描述： | LED DISPLAY DRIVER, PDSO8 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-8 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 335K |
| 代理商： | LX1992CDU |
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 7
Copyright
2000
Rev. 1.1b, 2005-03-03
W
M
.
C
LX1992
High Efficiency LED Driver
P
RODUCTION
D
ATA
S
HEET
TM
A P P L I C A T I O N I N F O R M A T I O N
( C O N T I N U E D )
Figure 5:
LXE1992 Engineering Evaluation Board
Table 1: Input and Ouput Pin Assignments
Pin Name
Allowable Range
Description
VBAT
0 to 6V
Main power supply for output. (Set external current limit to 0.5A)
LX1992 power. May be strapped to VBAT or use a separate supply if VCC jumper is in
the SEP position. Do not power output from VCC pin on board..
Potentiometer power. May be strapped to VBAT or use a separate supply if VPOT
jumper is in the SEP position. Do not power output from VPOT pin on board.
Apply a DC voltage or a PWM voltage to this pin to adjust the LED current. PWM
inputs should be greater than 120Hz and DC portion less than 350mV.
Pulled up to VCC on board (10K
), Ground to inhibit the LX1992.
VCC
1.6V to 6V
VPOT
1.6V to 6V
VADJ IN
0 to 350mV
/SHDN
0 to VCC
VOUT
0 to 18V
Power supply output voltage that is applied to LED string.
VFDBK
0 to 400mv
Sense resistor voltage. Divide this voltage by 15 to determine LED current.
Table 2: Jumper Pin Position Assignments
Jumper Position
Functional Description
VCC/ BAT
Use this position when powering VBAT and VCC from the same supply. Do not connect power to the VCC
input when using this jumper position.
VCC/ SEP
Use this position when using a separate VCC supply (different from VBAT).
VPOT/ VBAT
Use this position when powering the potentiometer reference circuit from the VBAT supply. Do not connect
power to the VCC input when using this jumper position.
Use this position when using a separate power supply (different from VBAT) to power the potentiometer
reference circuit. This will lower the VBAT current and provide a more accurate efficiency reading for the
LX1992 circuit.
VPOT/ SEP
ADJ/ POT
Use this position when using the potentiometer to adjust LED current.
ADJ/ EXT
Use this position when adjusting the LED current with an external PWM that has a repetition rate >120Hz. Or
when using a DC adjustment voltage.
Note: Always put jumpers in one of the two possible positions
A
P
P
L
I
C
A
T
I
O
N
相關PDF資料 |
PDF描述 |
|---|---|
| LX1992CLM | High Efficiency LED Driver |
| LX2202 | 2A Li-Ion Linear Charger and Power Control |
| LX2202CLQ | 2A Li-Ion Linear Charger and Power Control |
| LX2203A | Li-Ion Battery Charger |
| LX2203AILD | Li-Ion Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX1992-CDU | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
| LX1992CDU-TR | 制造商:Microsemi Corporation 功能描述:LED DRVR 4SEGMENT 1.6V TO 6V 8MSOP IN TUBES - Bulk |
| LX1992CLM | 功能描述:IC LED DRIVR WT/CLR BCKLGT 8-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| LX1992-CLM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
| LX1992EVALKIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Driver |
發布緊急采購，3分鐘左右您將得到回復。