- 您現在的位置：買賣IC網 > PDF目錄45008 > LX1689IPWT (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LX1689IPWT |
| 廠商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分類： | 穩壓器 |
| 英文描述： | FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 491K |
| 代理商： | LX1689IPWT |
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
Copyright
2000
Rev. 1.0c, 2004-02-23
WWW
.Microse
m
i
.CO
M
LX1689
Third Generation CCFL Controller
PRODUCTION DATA SHEET
I N T E GRA T ED
PR ODUC T S
FUNCTIONAL PIN DESCRIPTION ( C ONTI NUE D )
PIN NAME
DESCRIPTION
DIM_CLK
Digital Dimming Clock / Dimming Polarity. An input pin that may be selected to control burst frequency for
external Digital Dimming. This input can be any clock signal up to 200KHz. This pin is also used to control the
dimming polarity when operating in the analog or internal digital mode. If DIM_MODE is in the open condition
(Analog Dimming Mode) the DIM_CLK input should be connected to VDD_A for conventional dimming polarity
or set to Ground for reverse polarity. Conventional polarity means that lamp brightness increases with
increasing voltage on the BRITE_IN pin. Reverse polarity means that brightness decreases with increasing
voltage.
OC_SNS
Over Current Sense Input. A full wave AC voltage input centered on ground that is proportional to total high
voltage transformer secondary winding current. The OC_SNS input is full wave rectified, then applied to a digital
comparator with a 2V reference to cause peak voltages greater than 2V to digitally reset the PWM logic on a
pulse by pulse basis.
Frequency range of the input signal is 10kHz to 500KHz. Normal operating voltage levels should be under
max ±1.8VPK, and abnormal voltage can operate continuously as high as ± 10V peak under load fault
conditions. Transients under fault conditions can reach ± 25VPK.
DIM_MODE
Dimming Mode Input. This three state input pin places the IC in Analog Dimming Mode, internal Digital Dimming
Mode, or external Digital Dimming Mode. If the input is left open or forced to VDD_A / 2 Analog mode is
selected.
If connected to VDD_A, Digital Dimming with a external clock source applied to the DIM_CLK input is
selected to the burst timing generator. If connected to Ground, Digital Dimming with a internal clock is selected.
The internal clock is equivalent to the frequency at AOUT divided by two, both the internal or external clock
frequency can be divided down by setting the DIV_248 pin. (see DIV_248)
OV_SNS
Over Voltage Sense Input. A full wave AC voltage input centered around ground that is proportional to lamp
voltage. The OV_SNS input will be full wave rectified, then applied to a digital comparator with a 2V reference to
cause peak voltage greaten than 2V to digitally reset the PWM logic on a pulse by pulse basis.
Frequency range of the input signal is 10Khz to 500KHz. Normal operating voltage levels should be under
±1.8VPK, and abnormal voltage can operate continuously as high as ±10V peak under load fault conditions.
Transients under fault conditions can reach ± 25VPK.
The input has a 10K pull down resistor that serves as a DC restorer to the external capacitor that divides
down lamp voltage.
DIV_248
Divide Digital Dimming clock by 2, 4, or 8. This three state input pin causes the internal or external digital
dimming clock source to be divided by one of the three values, 2, 4, or 8. Its purpose is to allow a selection of
three possible burst rates for any given external or internal clock source. A high (VDD_A) selects divide by 2,
open selects divide by 4, and ground selects divided by 8. We advise keeping burst above 95Hz and below
about 400HZ. This will minimize visible flicker and possible audible noise from the power supply components.
I_SNS
Current Sense Input. A full wave AC voltage input centered around ground that is proportional to lamp current.
The I_SNS input is full wave rectified and amplified, then presented to the inverting input of the current error
amplifier through a 100K resistor.
Frequency range of the input signal is 10KHz to 500KHz. Normal operating voltage levels will be in the range
of ± 0.5 to 2.5VPK, and abnormal voltage can operate continuously as high as ± 10V peak under load fault
conditions. Transient under fault conditions can reach ± 25VPK. We strongly recommend a 10K resistor be
placed in series with the pin to limit current from voltage spikes that can occur by intermittent lamp connectors,
or arcing from a faulty high voltage transformer. This resistor will eliminate the possibility of IC damage under
these fault conditions.
The open lamp fault logic monitors the I_SNS pin voltage and number of lamp current cycles. If the number
of lamp current cycles with amplitude below fault threshold are less than 8 in a given fault checking period then
the strike latch will not be reset and a fault is declared, which shuts down the A/B outputs. In the strike mode, if
no lamp current is detected after 15 attempts a fault is likewise declared. ( See further LX1689 operation
section)
PP
AA
CC
KK
AA
GG
EE
DD
AA
TT
AA
相關PDF資料 |
PDF描述 |
|---|---|
| LX1689CPWT | FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 |
| LX1691AIPW-TR | 0.1 A FLUORESCENT LIGHT CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO16 |
| LX1692BIPW-TR | 0.1 A SWITCHING CONTROLLER, PDSO20 |
| LX1692IDW-TR | 0.1 A SWITCHING CONTROLLER, PDSO20 |
| LX1732CDUTR | 1 A SWITCHING REGULATOR, 135 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX1689IPWTR | 制造商:Microsemi Corporation 功能描述:CCFL Controller 3.3V/5V/9V/12V/15V/18V/24V 20-Pin TSSOP T/R |
| LX1689IPW-TR | 制造商:Microsemi Corporation 功能描述:CCFL DRVR 28V 20TSSOP - Tape and Reel |
| LX1691 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Enhanced Multi-Mode CCFL Controller |
| LX1691A | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Enhanced Multi-Mode CCFL Controller |
| LX1691AIPW | 功能描述:IC CTLR CCFL BACKLIGHT 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
發布緊急采購，3分鐘左右您將得到回復。