No.6000-6/21
LV4124W
Parameter
Symbol
Conditions
Ratings
Unit
min
typ
max
[RGB Signal and PCD Output Systems]
RGB signal and PCD output
DC voltage
Input SIG5 (VL = 0 mV) to (A), adjust the BRIGHT parameter
with the serial bus data so that T44 is 9 Vp-p, and measure
the DC voltages on T39, T41, T44, and T46.
VOUT
5.85
6.00
6.15
V
RGB signal and PCD output
DC voltage difference
Determine the maximum value of the differences in the
measured values of VOUT in the previous item for T39, T41,
T44, and T46.
VOUT
0
100
mV
VLIMMX
9.0
Vpp
RGB signal and PCD output
Color difference input balance
VLIMMN
5.2
Vpp
BRTMX
9.0
Vpp
Brightness variation
BRTMN
4.0
Vpp
PCD variation
PCDMX
9.0
Vpp
PCDMN
3
Vpp
Sub-brightness variation
SBBRT
±2.0
±3.0
V
Input SIG4 to (A) and determine the level difference between
the largest and the smallest of the noninverted output
amplitudes (white - black) for T41, T44, and T46.
RGB inter-signal gain difference
GRGB
–0.5
0
0.5
dB
RGB inverted/noninverted gain
difference
Input SIG4 to (A) and determine the difference between
the inverted output amplitude and the noninverted output
amplitude (white - black) for T41, T44, and T46.
GINV
–0.5
0
0.5
dB
RGB inter-signal black level
potential difference
Input SIG4 to (A) and determine the difference between the
highest and lowest black levels in the inverted and
noninverted T41, T44, and T46 outputs.
VBL
300
mV
G
γ
1
23.0
26.0
29.0
dB
Gamma gain
G
γ
2
12.0
15.0
18.0
dB
G
γ
3
18.0
21.0
25.0
dB
V
γ
1MN
0
IRE
Gamma 1 adjustment range
V
γ
1MX
70
IRE
V
γ
2MN
100
IRE
Gamma 2 adjustment range
V
γ
2MX
30
IRE
tPCDH
The transition time for a load of 8000 pF and an amplitude of
9 V p-p.
tPCDH: For rising edges. tPCDL: For falling edges.
2.5
μs
PCD transition time
tPCDL
2.5
μs
Input SIG3 to (A), and measure the maximum value
(VLIMMX) and minimum value (VLIMMN) of the voltage
range (black - black) over which the black limiter operates
when V54 is varied for T39, T41, T44, and T46.
Measure VLIMMX when V54 = 0 V, and measure VLIMMN
when V54 = 4.5 V.
Input SIG5 (VL = 0 mV) to (A) and set BRT to 0. Measure
the T41, T44, and T46 outputs (black - black).
Input SIG5 (VL = 0 mV) to (A) and measure the T39 output
(black - black) when P-BRT is set to 255.
Input SIG5 (VL = 0 mV) to (A) and measure the T44 output
(black - black) with respect to the T41 and T46 outputs
(black - black) when R-BRT = B-BRT = 0, and when R-BRT
= B-BRT = 255.
Input SIG8 to (A), adjust the T44 inverted output black level
to be 1.5 V with BRT, and adjust the amplitude (black -
white) to be 3.5 V with CONT. Measure VG1, VG2, and VG3
and calculate the following formulas.
G
γ
1 = 20log (VG1/0.0357)
G
γ
2 = 20log (VG2/0.0357)
G
γ
3 = 20log (VG3/0.0357)
Input SIG8 to (A) and set the T44 output (black - black) to 9
V p-p with the BRIGHT adjustment. Read the gamma gain
transition point at the input signal IRE level when
γ
1 = 0 and
when
γ
1 = 255.
V
γ
1MN is when
γ
1 = 0, and V
γ
1MX is when
γ
1 = 255.
Input SIG8 to (A) and set the T44 output (black - black) to 9
V p-p with the BRIGHT adjustment. Read the gamma gain
transition point at the input signal IRE level when
γ
2 = 0 and
when
γ
2 = 255.
V
γ
2MN is when
γ
2 = 0, and V
γ
2MX is when
γ
2 = 255.
Input SIG5 (VL = 0 mV) to (A) and set BRT to 255. Measure
the T41, T44, and T46 outputs (black - black).
Input SIG5 (VL = 0 mV) to (A) and measure the T39 output
(black - black) when P-BRT is set to 0.
AC Characteristics (3)