- 您現在的位置：買賣IC網 > PDF目錄367614 > LUCL9500AGF-DT High-Voltage Ringing SLIC for VolP Applications PDF資料下載
參數資料
| 型號： | LUCL9500AGF-DT |
| 英文描述： | High-Voltage Ringing SLIC for VolP Applications |
| 中文描述： | 高壓振鈴用戶接口應用的福爾普 |
| 文件頁數： | 21/32頁 |
| 文件大小： | 616K |
| 代理商： | LUCL9500AGF-DT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Preliminary Data Sheet
September 2001
High-Voltage Ringing SLIC for VoIP Applications
L9500A
Agere Systems Inc.
21
Applications
Power Control
Under normal device operating conditions, power dissi-
pation on the device must be controlled to prevent the
device temperature from rising above the thermal shut-
down and causing the device to shut down. Power dis-
sipation is highest with higher battery voltages, higher
current limit, and under shorter dc loop conditions.
Additionally, higher ambient temperature will also
reduce thermal margin.
To support required power ringing voltages, this device
is meant to operate with a high-voltage primary battery
(–65 V to –75 V typically). Thus, power control is nor-
mally achieved by use of the battery switch and an aux-
iliary lower absolute voltage battery. Operating
temperature range, maximum current limit, maximum
battery voltage, minimum dc loop length and protection
resistors values, airflow, and number of PC board lay-
ers will influence the overall thermal performance. The
following example illustrates typical thermal design
considerations.
The thermal resistance of the 28-pin PLCC package is
typically 35.5
°
C/W, which is representative of the natu-
ral airflow as seen in a typical switch cabinet with a
multilayer board.
The L9500 will enter thermal shutdown at a typical tem-
perature of 150
°
C. The thermal design should ensure
that the SLIC does not reach this temperature under
normal operating conditions.
For this example, assume a maximum ambient operat-
ing temperature of 85
°
C, a designed current limit of
30 mA, a maximum battery of –75 V, and an auxiliary
battery of –21 V. Assume a (worst-case) minimum dc
loop of 20
of wire resistance, 30
protection resis-
tors, and 200
for the handset. Additionally, include
the effects of parameter tolerance.
1. T
TSD
– T
AMBIENT(max)
= allowed thermal rise.
150°C – 85 °C = 65 °C.
2. Allowed thermal rise = package thermal
impedance
SLIC power dissipation.
65 °C = 35.5°C/W
SLIC power dissipation
SLIC power dissipation (P
D
) = 1.83 W.
Thus, if the total power dissipated in the SLIC is less
than 1.83 W, it will not enter the thermal shutdown
state. Total SLIC power is calculated as:
Total P
D
= maximum battery
maximum current
limit + SLIC quiescent power.
For the L9500A, the worst-case SLIC on-hook active
power is 64 mW. Thus,
Total off-hook power = (I
LOOP
)(current-limit
tolerance) * (V
BATAPPLIED
) + SLIC on-hook power
Total off-hook power = (0.030 A)(1.08) * (21) +
75 mW
Total off-hook power = 744.4 mW
The power dissipated in the SLIC is the total power dis-
sipation less the power that is dissipated in the loop.
SLIC P
D
= Total power – loop power
Loop off-hook power = (I
LOOP
* 1.08)
2
(R
LOOP(dc)
min + 2R
PROTECTION
+ R
HANDSET
)
Loop off-hook power = ((0.030 A)(1.08))
2
(20
+
60
+ 200
)
Loop off-hook power = 293.9 mW
SLIC off-hook power = Total off-hook power – loop
off-hook power
SLIC off-hook power = 744.4 mW – 293.9 mW
SLIC off-hook power = 450.5 mW < 1.83 W
Thus, under the worst-case normal operating condi-
tions of this example, the thermal design, using the
auxiliary, is adequate to ensure the device is not driven
into thermal shutdown under worst-case operating con-
ditions.
相關PDF資料 |
PDF描述 |
|---|---|
| LUCW3000CCN | W3000 PLL Dual-Band Frequency Synthesizer |
| LUCW3000CCN-TR | W3000 PLL Dual-Band Frequency Synthesizer |
| LUCW3011FCL | 1 GHz Quadrature Modulator |
| LUCW3020CCS | GSM Multiband RF Transceiver |
| LUCW3020CCS-DB | GSM Multiband RF Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9500ARG-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:High-Voltage Ringing SLIC for VolP Applications |
| LUCLX6B | 制造商:Schneider Electric 功能描述:Magnetic Control unit,24Vac,0.6A |
| LUCLX6BL | 制造商:Schneider Electric 功能描述:Magnetic Control Unit,24Vdc,0.6A |
| LUCLX6ES | 制造商:Schneider Electric 功能描述:Magnetic Control Unit,48-72V,0.6A |
| LUCLX6FU | 制造商:Schneider Electric 功能描述:Magnetic Control Unit,110-240V,0.6A |
發布緊急采購，3分鐘左右您將得到回復。