- 您現在的位置：買賣IC網 > PDF目錄369872 > LUCL9311GP-D Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access PDF資料下載
參數資料
| 型號： | LUCL9311GP-D |
| 英文描述： | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
| 中文描述： | 線路接口和線路接入電路全功能用戶接口高縱向平衡，振鈴繼電器，和GR - 909測試訪問 |
| 文件頁數： | 42/50頁 |
| 文件大?。?/td> | 852K |
| 代理商： | LUCL9311GP-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Data Sheet
July 2001
Ringing Relay, and GR-909 Test Access
L9311 Full-Feature SLIC with High Longitudinal Balance,
42
Agere Systems Inc.
ac Applications
(continued)
ac Interface Network
(continued)
Thus, it appears the solution is to have a SLIC with a
low gain, especially in the receive direction. This will
allow the codec to operate near its maximum output
signal (to optimize S/N), without an external resistor
divider (to minimize cost).
Note also that some third-generation codecs require
the designer to provide an inherent resistive termina-
tion via external networks. The codec will then provide
gain shaping, as a function of frequency, to meet the
return loss requirements. Further stability issues may
add external components or excessive ground plane
requirements to the design.
To meet the unique requirements of both types of
codecs, the L9311 offers two receive gain choices.
These receive gains are mask programmable at the
factory and are offered as two different code variations.
For interface with a first-generation codec, the L9311 is
offered with a receive gain of 8. For interface with a
third-generation codec, the L9311 is offered with a
receive gain of 2. In either case, the transconductance
in the transmit direction, or the transmit gain, is 300
.
This selection of receive gain gives the designer the
flexibility to maximize performance and minimize exter-
nal components, regardless of the type of codec cho-
sen.
Design Tools
The following examples illustrate the design tech-
niques/equations followed to design the ac interface
with a first- or third-generation codec for both a resis-
tive and complex design. To aid the line circuit design,
Agere has available Windows*-based spreadsheets to
do the individual component calculations. Further,
Agere has available PSPICE
models for circuit simula-
tion and verification. Consult your Agere Account Rep-
resentative to obtain these design tools.
First-Generation Codec ac Interface Network
Termination impedance may be specified as purely
resistive or complex, that is, some combination of
resistors and capacitors that causes the impedance to
vary with frequency. The design for a pure resistive ter-
mination, such as 600
, does not vary with frequency,
so it is somewhat more straightforward than a complex
termination design. For this reason, the case of a resis-
tive design and complex design will be shown sepa-
rately.
First-Generation Codec ac Interface Net-
work: Resistive Termination
The following reference circuit shows the complete
SLIC schematic for interface to the Agere T7504 first-
generation codec for a resistive termination imped-
ance. For this example, the ac interface was designed
for a 600
resistive termination and hybrid balance
with transmit gain and receive gain set to 0 dBm.
Also, this example illustrates the device with a single
battery operation, fixed current limit, and fixed loop clo-
sure threshold. This is a lower feature application
example.
Resistor R
GN
is optional. It compensates for any mis-
match of input bias voltage at the RCVN/RCVP inputs.
If it is not used, there may be a slight offset at tip and
ring due to mismatch of input bias voltage at the
RCVN/RCVP inputs. It is very common to simply tie
RCVN directly to ground in this particular mode of oper-
ation. If used, to calculate R
GN
, the impedance from
RCVN to ac ground should equal the impedance from
RCVP to ac ground.
*
Windows
is a registered trademark of Microsoft Corporation.
PSPICE
is a registered trademark of MicroSim Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9311GP0DT | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
| LUCL9313AP-D | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| LUCL9313AP-DT | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| LUCL9313GP-D | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| LUCL9313GP-DT | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9312AP-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| LUCL9312AP-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| LUCL9312GP-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| LUCL9312GP-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| LUCL9313AP-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
發布緊急采購，3分鐘左右您將得到回復。