- 您現在的位置：買賣IC網 > PDF目錄377786 > LTJD (Linear Technology Corporation) 2.5MHz, Over-The-Top Low Power, Rail-to-Rail Input and Output Op Amp in SOT-23 PDF資料下載
參數資料
| 型號： | LTJD |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 2.5MHz, Over-The-Top Low Power, Rail-to-Rail Input and Output Op Amp in SOT-23 |
| 中文描述： | 2.5MHz的，過度的，前低功耗，軌至軌輸入和輸出運算放大器采用SOT - 23 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 217K |
| 代理商： | LTJD |
9
LT1784
APPLICATIOU
Supply Voltage
The positive supply pin of the LT1784 should be bypassed
with a small capacitor (typically 0.1
μ
F) within an inch of
the pin. When driving heavy loads, and additional 4.7
μ
F
electrolytic capacitor should be used. When using split
supplies the same is true for the negative supply pin.
The LT1784 is protected against reverse battery voltages
up to 18V. In the event a reverse battery condition occurs
the supply current is less than 1nA.
W
U
U
Inputs
The LT1784 has two input stages, NPN and PNP (see
the Simplified Schematic), resulting in three distinct
operating regions as shown in the “Input Bias Current vs
Common Mode” Typical Performance Characteristic Curve.
For input voltages about 1V or more below V
+
, the PNP
input stage is active and the input bias current is typically
–250nA. When the input common mode voltage is within
0.6V of the positive rail, the NPN stage is operating and the
input bias current is typically 500nA. Increases in tem-
perature will cause the voltage at which operation switches
from the PNP input stage to the NPN input stage to move
towards V
+
. The input offset voltage of the NPN stage is
untrimmed and is typically 3mV.
A Schottky diode in the collector of the input transistors,
along with special geometries for these NPN transistors,
allow the LT1784 to operate with either or both of its inputs
above V
+
. At about 0.3V above V
+
, the NPN input transis-
tors is fully saturated and the input bias current is typically
200
μ
A at room temperature. The input offset voltage is
typically 3mV when operating above V
+
. The LT1784 will
operate with inputs 18V above V
–
regardless of V
+
.
The inputs are protected against excursions as much as
10V below V
–
by an internal 1k resistor in series with each
input and a diode from the input to the negative supply.
The input stage of the LT1784 incorporates phase reversal
protection to prevent the output from phase reversing for
inputs up to 9V below V
–
. There are no clamping diodes
between the inputs and the maximum differential input
voltage is 18V.
Output
The output of the LT1784 can swing to within 80mV of the
positive rail and within 4mV of the negative rail with no
load. When monitoring input voltages within 80mV of the
positive rail or within 4mV of the negative rail, gain should
be taken to keep the output from clipping. The LT1784 can
typically sink and source over 25mA at
±
5V supplies,
sourcing current is reduced to 7.5mA at 3V total supplies
as noted in the electrical characteristics.
The LT1784 is internally compensated to drive at least
400pF of capacitance under any output loading condi-
tions. A 0.22
μ
F capacitor in series with a 150
resistor
between the output and ground will compensate these
amplifiers for larger capacitive loads, up to 10,000pF at all
output currents.
Distortion
There are two main contributors to distortion in op amps:
output crossover distortion as the output transitions from
sourcing to sinking current, and distortion caused by
nonlinear common mode rejection. If the op amp is
operating inverting, there is no common mode induced
distortion. If the op amp is operating in the PNP input stage
(input not within 1V of V
+
), the CMRR is very good,
typically 95dB. When the LT1784 switches between input
stages, there is significant nonlinearity in the CMRR.
Lower load resistance increases the output crossover
distortion but has no effect on the input stage transition
distortion. For lowest distortion, the LT1784 should be
operated single supply, with the output always sourcing
current and with the input voltage swing between ground
and (V
+
–1V). See Typical Performance Characteristics
Curve, “Total Harmonic Distortion + Noise vs Output
Voltage Amplitude.”
Gain
The open-loop gain is almost independent of load when
the output is sourcing current. This optimizes perfor-
mance in single supply applications where the load is
returned to ground. The Typical Performance Characteric
Curve “Open-Loop Gain” for various loads shows the
details.
相關PDF資料 |
PDF描述 |
|---|---|
| LTSN | 2.5MHz, Over-The-Top Low Power, Rail-to-Rail Input and Output Op Amp in SOT-23 |
| LTK001 | Thermocouple Cold Junction Compensator and Matched Amplifier |
| LTK00CN8 | Thermocouple Cold Junction Compensator and Matched Amplifier |
| LTK00MH | Thermocouple Cold Junction Compensator and Matched Amplifier |
| LTK01CN8 | Thermocouple Cold Junction Compensator and Matched Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTK | 功能描述:TIP REPLACEMENT 1.2MM FOR WS RoHS:是 類別:焊接、脫焊、返修產品 >> 尖端，噴嘴 系列:Weller®, LT 標準包裝:1 系列:SFP 尖端 - 類型:焊接 尖端 - 尺寸:0.016 英寸 OD x 0.34 英寸 L（0.41mm x 8.5mm） 尖端 - 形狀:圓錐形 溫度范圍:- 適用于相關產品:SP200-21，SP200-11 配用:389-1137-ND - HANDPIECE SOLDERING CARTRIDGEMFR-2211-ND - SYSTEM SOLDER 2OUTPUT 100/240VAC |
| LT-K | 功能描述:烙鐵 Weller Chisel Tip .047" x .73" Reach RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| LTK001 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Thermocouple Cold Junction Compensator and Matched Amplifier |
| LTK001_09 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Thermocouple Cold Junction Compensator and Matched Amplifier |
| LTK001ACN | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Thermocouple Cold Junction Compensator and Matched Amplifier |
發布緊急采購，3分鐘左右您將得到回復。