參數資料
型號: LTCMN
廠商: Linear Technology Corporation
元件分類: 運動控制電子
英文描述: Dual High Voltage, High Side Current Sense Amplifier
中文描述: 雙高電壓,高側電流檢測放大器
文件頁數: 7/16頁
文件大小: 267K
代理商: LTCMN
LTC6103
7
6103f
APPLICATIONS INFORMATION
In this dual current sense device, amplifiers A and B are
independent except for sharing the same V
pin. So supply
voltage and component values can be chosen independently
for each amplifier.
Selection of External Current Sense Resistor
The external sense resistor, R
SENSE
, has a significant effect
on the function of a current sensing system and must be
chosen with care.
First, the power dissipation in the resistor should be
considered. The system load current will cause both heat
and voltage loss in R
SENSE
. As a result, the sense resis-
tor should be as small as possible while still providing
the input dynamic range required by the measurement.
Note that input dynamic range is the difference between
the maximum input signal and the minimum accurately
reproduced signal, and is limited primarily by input DC
offset of the internal amplifier of the LTC6103.
As an example, an application may require that the
maximum sense voltage be 100mV. If this application is
expected to draw 2A at peak load, R
SENSE
should be no
larger than 50m
Ω
.
V
I
A
PEAK
2
R
mV
m
SENSE
SENSE
=
=
=
100
50
Once the maximum R
SENSE
value is determined, the mini-
mum sense resistor value will be set by the resolution or
dynamic range required. The minimum signal that can be
accurately represented by this sense amp is limited by the
input offset. As an example, the LTC6103 has a typical
input offset of 85μV. If the minimum current is 20mA, a
sense resistor of 4.25m
Ω
will set V
SENSE
to 85μV. This is
the same value as the input offset. A larger sense resistor
will reduce the error due to offset by increasing the sense
voltage for a given load current.
Choosing a 50m
Ω
R
SENSE
will maximize the dynamic range
and provide a system that has 100mV across the sense
resistor at peak load (2A), while input offset causes an
error equivalent to only 1.7mA of load current.
Peak dissipation is 200mW. If instead a 5m
Ω
sense resis-
tor is employed, then the effective current error is 17mA,
while the peak sense voltage is reduced to 10mV at 2A,
dissipating only 20mW.
The low offset and corresponding large dynamic range of
the LTC6103 make it more flexible than other solutions
in this respect. The 85μV typical offset gives 60dB of
dynamic range for a sense voltage that is limited to 85mV
max, and over 75dB of dynamic range for a maximum
input of 500mV.
THEORY OF OPERATION
An internal sense amplifier loop forces –IN to have the
same potential as +IN. Connecting an external resistor, R
IN
,
between –IN and V
+
forces a potential across R
IN
that is the
same as the sense voltage across R
SENSE
. A corresponding
current, (I
LOAD
+ I
S
) R
SENSE
/R
IN
, will flow through R
IN
.
The high impedance inputs of the sense amplifier will not
conduct this input current, so the current will flow through
an internal MOSFET to the OUT pin. In most application
cases, I
S
<< I
LOAD
, so I
OUT
≈ I
LOAD
R
SENSE
/R
IN
.
The output current can be transformed into a voltage by
adding a resistor from OUT to V
. The output voltage is
then V
OUT
= (V
) + (I
OUT
R
OUT
).
相關PDF資料
PDF描述
LTC6241HVIDD Dual/Quad 18MHz, Low Noise, Rail-to-Rail, CMOS Op Amps
LTC6242CDHC Dual/Quad 18MHz, Low Noise, Rail-to-Rail, CMOS Op Amps
LTC6242IDHC Dual/Quad 18MHz, Low Noise, Rail-to-Rail, CMOS Op Amps
LTC6241 Dual/Quad 18MHz, Low Noise, Rail-to-Rail, CMOS Op Amps
LTC6241CDD Dual/Quad 18MHz, Low Noise, Rail-to-Rail, CMOS Op Amps
相關代理商/技術參數
參數描述
LTCMR5070 制造商:PREMIER FARNELL 功能描述:DWO SONY EFFIO BULLET CAM 700T2.8-12MM LENS WHITE
LTCMR8270B 制造商:MCM 功能描述:COLOR 1/3CCD D/N BOX BULLET 700TVL; 2.8-10MM; 42LEDS BLK
LTCMR8270W 制造商:MCM 功能描述:COLOR 1/3CCD D/N BOX BULLET 700TVL; 2.8-10MM; 42LEDS WHITE
LTCMT2070BD 制造商:MCM 功能描述:SONY EFFIO DSP DOME CAM-700TVL2.8-12MM LENS GREY
LTCMT2070D 制造商:MCM 功能描述:SONY EFFIO DSP DOME CAM-700TVL2.8-12MM LENS WHITE