- 您現在的位置：買賣IC網 > PDF目錄9473 > LTC6990CDCB#TRPBF (Linear Technology)IC OSC SILICON 1MHZ 6DFN PDF資料下載
參數資料
| 型號： | LTC6990CDCB#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 9/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC SILICON 1MHZ 6DFN |
| 產品培訓模塊： | TimerBlox Family Timing Devices |
| 特色產品： | TimerBlox? |
| 標準包裝： | 2,500 |
| 系列： | TimerBlox® |
| 類型： | 振蕩器 - 硅 |
| 頻率： | 488Hz ~ 1MHz |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 電流 - 電源： | 235µA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 6-WFDFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
| 供應商設備封裝： | 6-DFN-EP（2x3） |
| 安裝類型： | 表面貼裝 |
| 配用： | DC1562A-A-ND - BOARD EVAL LTC6990 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LTC6990
17
6990fc
For more information www.linear.com/LTC6990
Figure 12. VCO Transfer Function
VCTRL (V)
1
f OUT
(kHz)
100
80
40
20
60
0
2
6990 F12
4
3
APPLICATIONS INFORMATION
Step 4: Calculate and Select RSET
The final step is to calculate the correct value for RSET
using the following equation:
RSET =
1MHz 50k
NDIV f(0V) VSET KVCO
(
)
(3e)
Select the standard resistor value closest to the calculated
value.
Some applications require combinations of fOUT(MIN),
fOUT(MAX), VCTRL(MIN) and VCTRL(MAX) that are not achiev-
able. These applications result in unrealistic or unrealiz-
able (e.g. negative value) resistors. These applications
will require preconditioning of the VCTRL signal via range
scaling and/or level shifting to place the VCTRL into a range
that yields realistic resistor values.
Frequency Error in VCO Applications Due to VSET Error
As stated earlier, f(0V) represents the frequency for VCTRL
= 0V, which is the same value as would be generated by
a single resistor between SET and GND with a value of
RSET || RVCO. Therefore, f(0V) is not affected by error or
drift in VSET (i.e. VSET adds no frequency error when
VCTRL = 0V).
The accuracy of KVCO does depend on VSET because the
output frequency is controlled by the ratio of VCTRL to
VSET. The frequency error (in Hertz) due to VSET is ap-
proximated by:
fOUT KVCO VCTRL
VSET
As the equation indicates, the potential for error in output
frequency due to VSET error increases with KVCO and is
at its largest when VCTRL is at its maximum. Recall that
when VCTRL is at its maximum, the output frequency is
at its minimum. With the maximum absolute frequency
error (in Hertz) occurring at the lowest output frequency,
the relative frequency error (in percent) can be significant.
VSET is nominally 1.0V with a maximum error of ±30mV
for at most a ±3% error term. However, this ±3% po-
tential error term is multiplied by both VCTRL and KVCO.
Wide frequency range applications (high KVCO) can have
frequency errors greater than ±50% at the highest VCTRL
voltage (lowest fOUT). For this reason the simple, two
resistor VCO circuit must be used with caution for ap-
plications where the frequency range is greater than 4:1.
Restricting the range to 4:1 typically keeps the frequency
error due to VSET variation below 10%.
For wide frequency range applications, the non-inverting
VCO circuit shown in Figure 13 is preferred because the
maximum frequency error occurs when the frequency
is highest, keeping the relative error (in percent) much
smaller.
Example: Design a VCO with the Following Parameters
fOUT(MAX) = 100kHz at VCTRL(MIN) = 1V
fOUT(MIN) = 10kHz at VCTRL(MAX) = 4V
Step 1: Select the NDIV Value
First, choose an NDIV that meets the requirements of
Equation (3a).
6.25 ≤ NDIV ≤ 10
The application’s desired frequency range is 10:1, which
isn’t always possible. However, in this case NDIV=8meets
both requirements of Equation (3).
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1290BIN | IC DATA ACQ SYS 12BIT 20-DIP |
| VE-21Y-MX-S | CONVERTER MOD DC/DC 3.3V 49.5W |
| LTC6990CS6#TRMPBF | IC OSC SILICON 1MHZ TSOT23-6 |
| AD7891BP-1REEL | IC DAS 12BIT 8CH 44-PLCC |
| VE-21Y-MW-S | CONVERTER MOD DC/DC 3.3V 66W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC6990CS6#PBF | 制造商:Linear Technology 功能描述:TIMERBLOX: VOLTAGE CONTROLLED SILICON OSCILLATOR 制造商:Linear Technology 功能描述:IC VOLTAGE CONTROLLED OSCILLATOR SOT23-6 制造商:Linear Technology 功能描述:IC VOLTAGE CONTROLLED OSCILLATOR SOT23-6; Operating Mode:-; Frequency:2MHz; Supply Voltage Min:2.25V; Supply Voltage Max:5.5V; Digital IC Case Style:SOT-23; No. of Pins:6; Clock External Input:Yes; Operating Temperature Min:0C ;RoHS Compliant: Yes |
| LTC6990CS6#TRMPBF | 功能描述:IC OSC SILICON 1MHZ TSOT23-6 RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:TimerBlox® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器（TCXO） 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝 |
| LTC6990CS6#TRPBF | 功能描述:IC OSC SILICON 1MHZ TSOT23-6 RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:TimerBlox® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器（TCXO） 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝 |
| LTC6990CS6PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:TimerBlox: Voltage Controlled Silicon Oscillator |
| LTC6990CS6-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:TimerBlox: Voltage Controlled Silicon Oscillator |
發布緊急采購，3分鐘左右您將得到回復。