- 您現在的位置：買賣IC網 > PDF目錄9515 > LTC6909CMS#PBF (Linear Technology)IC OSC SILICON 6.67MHZ 16-MSOP PDF資料下載
參數資料
| 型號： | LTC6909CMS#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 19/22頁 |
| 文件大小： | 0K |
| 描述： | IC OSC SILICON 6.67MHZ 16-MSOP |
| 產品目錄繪圖： | 16-MSOP |
| 標準包裝： | 37 |
| 類型： | 振蕩器 - 硅 |
| 頻率： | 12.5kHz ~ 6.67MHz |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電流 - 電源： | 2.4mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 16-TFSOP（0.118"，3.00mm 寬） |
| 包裝： | 管件 |
| 供應商設備封裝： | 16-MSOP |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 1715 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁
LTC6909
6
6909fa
V+A (Pin 1): Analog Voltage Supply (2.7V ≤ V+A ≤ 5.5V).
This supply should be kept free of noise and ripple. It
should be bypassed directly to GND with a 0.1F or greater
low ESR capacitor. V+A and V+D must be connected to the
same supply voltage.
GND (Pin 2): Ground Connections. Should be tied to a
ground plane for best performance.
PH0, PH1, PH2 (Pins 3, 4, 15): Output Phasing Selec-
tion Pins. These are standard CMOS logic input pins and
they do not have an internal pull-up or pull-down. These
pins must be connected to a valid logic input 0 or 1 volt-
age. Connect the pins to GND for a logic 0 and to the V+D
pin for a logic 1. These pins configure the output phase
relationships as follows:
PH2
PH1
PH0
MODE
0
All Outputs Are Floating (Hi-Z)
0
1
All Outputs Are Held Low
0
1
0
3-Phase Mode (PH = 3)
0
1
4-Phase Mode (PH = 4)
1
0
5-Phase Mode (PH = 5)
1
0
1
6-Phase Mode (PH = 6)
1
0
7-Phase Mode (PH = 7)
1
8-Phase Mode (PH = 8)
The PH0, PH1, PH2 pin connections not only determine
the phase relationship of the output signals but also divide
the master oscillator frequency by the value PH.
OUT1 Through OUT8 (Pins 5 Through 12): Oscillator
Outputs. These are CMOS rail-to-rail logic outputs with
a series resistance of approximately 40Ω, capable of
driving 1k and/or 50pF loads. Larger loads may cause
minor frequency inaccuracies due to supply bounce at
high frequencies. When any output pin is not in use, it is
in a floating, high impedance state. The outputs are also
held in a high impedance state during start-up. After the
part’s internal frequency setting loop has settled, the out-
puts are active, clean and operating at the set frequency
(first cycle accurate).
V+D (Pin 13): Digital Voltage Supply (2.7V ≤ V+D ≤ 5.5V).
This pin should be bypassed directly to GND with a 0.1F
or greater low ESR capacitor. V+D and V+A must be con-
nected to the same supply voltage.
MOD (Pin 14): Spread Spectrum Frequency Modulation
Setting Input. This input selects among four modulation
rate settings. The MOD pin should be tied to ground for
an fOUT/16 modulation rate. Floating the MOD pin selects
an fOUT/32 modulation rate. The MOD pin should be tied
to V+D for the fOUT/64 modulation rate. Tying one of the
active outputs to the MOD pin turns the modulation off.
To detect a floating MOD pin, the LTC6909 attempts to
pull the pin to the midsupply point. This is realized with
two internal current sources, one tied to V+D and MOD
and the other one tied to GND and MOD. Therefore, driv-
ing the MOD pin high requires sourcing approximately
2A. Likewise, driving the MOD pin low requires sinking
approximately 2A. When the MOD pin is floated for the
fOUT/32 modulation rate, it must be bypassed using a
1nF or larger, capacitor to GND. Any AC signal coupling
to the MOD pin could potentially be detected and stop the
frequency modulation.
SET (Pin 16): Frequency Setting Resistor Input. The value
of the resistor connected between this pin and V+A deter-
mines the frequency of the master oscillator. The output
frequency, fOUT, is the master oscillator frequency divided
by PH as set by the PH0, PH1 and PH2 pin connections.
The voltage on this pin is held approximately 1.1V below
V+A. For best performance, use a precision metal film
resistor with a value between 20k and 400k, and limit the
capacitance on the pin to less than 10pF. Resistor values
outside of this range will have some loss of accuracy as
noted in the Electrical Characteristics table.
pin Functions
相關PDF資料 |
PDF描述 |
|---|---|
| LTC6991HS6#TRMPBF | IC OSC SILICON 977HZ TSOT23-6 |
| MS27473T20B39SB | CONN PLUG 39POS STRAIGHT W/SCKT |
| M83723/75W1624N | CONN PLUG 24POS STRAIGHT W/SCKT |
| M83723/75R1624N | CONN PLUG 24POS STRAIGHT W/SCKT |
| V28A48M200BF2 | CONVERTER MOD DC/DC 48V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC6909CMS-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1 to 8 Output, Multiphase Silicon Oscillator with Spread Spectrum Modulation |
| LTC6909HMS#PBF | 功能描述:IC OSC SILICON 6.67MHZ 16-MSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:- 標準包裝:3,000 系列:- 類型:振蕩器 - 晶體 計數:- 頻率:- 電源電壓:2.3 V ~ 5.5 V 電流 - 電源:1.07mA 工作溫度:-30°C ~ 80°C 封裝/外殼:SOT-665 包裝:帶卷 (TR) 供應商設備封裝:SS迷你型-5D 安裝類型:表面貼裝 其它名稱:AN8955SSMTXLTR |
| LTC6909HMS#TRPBF | 功能描述:IC OSC SILICON 6.67MHZ 16-MSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 可編程計時器和振蕩器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:45 系列:- 類型:溫度 - 補償晶體振蕩器（TCXO） 計數:- 頻率:25MHz 電源電壓:3.135 V ~ 3.465 V 電流 - 電源:1.5mA 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 包裝:管件 供應商設備封裝:16-SOIC W 安裝類型:表面貼裝 |
| LTC6909HMS-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1 to 8 Output, Multiphase Silicon Oscillator with Spread Spectrum Modulation |
| LTC6909HMS-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1 to 8 Output, Multiphase Silicon Oscillator with Spread Spectrum Modulation |
發布緊急采購，3分鐘左右您將得到回復。