
LTC6603
18
6603fa
APPLICATIONS INFORMATION
than 100k. If the value of RBIAS is too large, the lters will
not receive a large enough bias current, possibly causing
errors due to insufcient settling. Be sure to obey the
absolute maximum specications when driving a clock
into CLKIO (Pin 15).
Input Common Mode and Differential Voltage Range
The input signal range extends from zero to the V+IN
supply voltage. This input supply can be tied to V+A and
V+D, or driven up to 5.5V for increased input signal range.
Figure 9 shows the distortion of the lter versus common
mode input voltage with a 2VP-P differential input signal
(V+IN = 5V).
control bits LPF1 and LPF0. The differential input imped-
ance is a function of the clock frequency and the control
bits LPF1, LPF0, GAIN1 and GAIN0. Table 5 shows the
typical input impedances for a clock frequency of 80MHz.
These input impedances are all proportional to 1/fCLK, so
if the clock frequency were reduced by half to 40MHz,
the impedances would be doubled. The typical variation
in dynamic input impedance for a given clock frequency
is –20% to +35%.
Table 5. Differential, Common Mode Input Impedances,
fCLK = 80MHz
GAIN1 GAIN0 LPF1
LPF0
DIFFERENTIAL
INPUT IMPEDANCE
(kΩ)
COMMON MODE
INPUT IMPEDANCE
(kΩ)
0000
38
40
0001
16
20
0010
2.5
5
0011
2.5
5
0100
20
40
0101
9.5
20
0
1
0
2.5
5
0
1
2.5
5
1
0
10
40
1
0
1
5.4
20
1010
1.9
5
1011
1.9
5
1
0
5.2
40
1
0
1
2.8
20
1110
1.6
5
1111
1.6
5
Output Common Mode and Differential Voltage Range
The output voltage is a fully differential signal with a
common mode level equal to the voltage at VOCM. Any of
the lter outputs may be used as single-ended outputs,
although this will degrade the performance. The output
voltage range is typically 0.5V to V+A – 0.5V (V+A = 2.7V
to 3.6V).
The common mode output voltage can be adjusted by
overdriving the voltage present on VOCM. To maximize
the undistorted peak-to-peak signal swing of the lter,
the VOCM voltage should be set to V+A/2. Note that the
output common mode voltages of the two channels are
Figure 9. Distortion vs Common Mode Input Voltage (5V)
COMMON MODE INPUT VOLTAGE (V)
1.0
DISTOR
TION
(dBc)
–60
–70
–80
–90
3.0
2.0
4.0
6603 F09
5.0
2.5
4.5
1.5
3.5
RBIAS = 30.9k, VS = 3V, V+IN = 5.5V
LPF1 = 1, BW = 2.5MHz, GAIN = 24dB
VOUT = VP-P, TA = 25°C
HD3, f = 1MHz
HD3, f = 200kHz
For best performance, the inputs should be driven dif-
ferentially. For single-ended signals, connect the unused
input to VOCM (Pin 3) or to a quiet DC reference voltage.
To achieve the best distortion performance, the input
signal should be centered around the DC voltage of the
unused input.
Refer to the Typical Performance Characteristics section
to estimate the distortion for a given input level.
Dynamic Input Impedance
The unique input sampling structure of the LTC6603
has a dynamic input impedance which depends on the
conguration and the clock frequency. This dynamic
input impedance has both a differential component and
a common mode component. The common mode input
impedance is a function of the clock frequency and the