- 您現在的位置：買賣IC網 > PDF目錄11614 > LTC4312CDE#TRPBF (Linear Technology)IC MULTIPLEXER 14-DFN PDF資料下載
參數資料
| 型號： | LTC4312CDE#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MULTIPLEXER 14-DFN |
| 標準包裝： | 2,500 |
| 系列： | * |
LTC4312
14
4312f
APPLICATIONS INFORMATION
Nested Addressing
The LTC4312 can provide nested addressing when its
ENABLE pins are used as channel select bits. This is
shown in Figure 7 where the master communicates with
slave devices that have the same address by selectively
enabling only one output channel at a time. Since slaves
have the same address care must be taken that the master
never enables both channels at the same time.
Stop Bit Generation and FAULT Clocking
If the output bus sticks low (SCLOUT or SDAOUT stuck
low for at least 45ms) on one of the enabled channels
and DISCEN is high, the LTC4312 attempts to unstick the
bus by rst breaking the connection between the input
and output, asserting FAULT low and generating up to
16 clock pulses at 5.5kHz on the SCLOUT node common
to the two channels. Should the stuck bus release high
during this period, clock pulsing is stopped, a stop bit is
generated and FAULT is cleared. In order for a connec-
tion to be established between the input and output, all
ENABLEs have to be taken low followed by an assertion
of the ENABLEs of the required channels.This process is
illustrated in Figure 8 for the case where only channel 1 is
active and SDAOUT1 starts out stuck low and then recov-
ers. If DISCEN is tied low and a stuck low event occurs,
the FAULT ag is driven low, but the connection between
the input and output is not broken and clock generation
is not done.
LTC4312
GND
VCC
VCC2
4312 F07
SCLOUT1
SDAOUT1
SCLOUT2
SDAOUT2
SCLIN
SDAIN
ENABLE1
ENABLE2
ACC
DISCEN
FAULT
ENABLE1
ENABLE2
3.3V
R3
10k
FAULT
R2
10k
R1
10k
C1
0.01μF
C2
0.01μF
3.3V
R5
10k
R4
10k
ADDRESS = 1001 000
5V
R7
10k
R6
10k
I2C
DEVICE
I2C
DEVICE
I2C
DEVICE
Figure 7. Nested Addressing
Figure 8.Bus Waveforms During a SDAOUT Stuck Low and Recovery Event
1ms/DIV
4312 F08
CONNECT AT RISING EDGE OF ENABLE1
DISCONNECT
AT TIMEOUT
STUCK LOW > 45ms
AUTOMATIC CLOCKING
DRIVEN LOW
RECOVERS
SCLOUT1
5V/DIV
SDAOUT1
5V/DIV
SDAIN
5V/DIV
ENABLE1
5V/DIV
相關PDF資料 |
PDF描述 |
|---|---|
| V24A5C400BL2 | CONVERTER MOD DC/DC 5V 400W |
| LTC4312CMS#TRPBF | IC MULTIPLEXER 16-MSOP |
| V24A5C400B2 | CONVERTER MOD DC/DC 5V 400W |
| V24A5C400B | CONVERTER MOD DC/DC 5V 400W |
| LTC4311ISC6#TRPBF | IC ACCELERATOR SMBUS DL SC70-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4312CMS#PBF | 功能描述:IC MULTIPLEXER 16-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
| LTC4312CMS#TRPBF | 功能描述:IC MULTIPLEXER 16-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
| LTC4312IDE#PBF | 功能描述:IC MULTIPLEXER 14-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
| LTC4312IDE#TRPBF | 功能描述:IC MULTIPLEXER 14-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
| LTC4312IMS#PBF | 功能描述:IC MULTIPLEXER 16-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 信號緩沖器，中繼器，分配器 系列:* 標準包裝:160 系列:- 類型:轉發器 Tx/Rx類型:以太網 延遲時間:- 電容 - 輸入:- 電源電壓:2.37 V ~ 2.63 V 電流 - 電源:60mA 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:托盤 其它名稱:Q5134101 |
發布緊急采購，3分鐘左右您將得到回復。