參數資料
型號: LTC4304IDD#TRPBF
廠商: Linear Technology
文件頁數: 5/16頁
文件大?。?/td> 644K
描述: IC BUS BUFFER I2C 10-DFN
產品培訓模塊: LTC4310 - Hot-Swappable I²C Isolators
標準包裝: 2,500
類型: 熱交換開關
應用: 通用型緩沖器/總線擴展器
內部開關:
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤
供應商設備封裝: 10-DFN(3x3)
包裝: 帶卷 (TR)
LTC4304
5
4304fa
ENABLE (Pin 1): Connection  Enable.  This  is  a  digital 
threshold input pin. For normal operation ENABLE is high.
Driving ENABLE below 0.8V isolates SDAIN from SDAOUT,
SCLIN from SCLOUT, asserts READY low and disables
automatic clocking. A rising edge on ENABLE after a fault
has occurred unconditionally forces a connection between
SDAIN, SDAOUT and SCLIN, SCLOUT.
SCLOUT (Pin 2): Serial Clock Output. Connect this pin to 
the SCL bus on the card.
SCLIN (Pin 3): Serial Clock Input. Connect this pin to SCL 
on the bus backplane.
ACC (Pin 4): Rise-Time Accelerator Control. Connect ACC 
to V
CC
 to disable all four accelerators. Connect ACC to
GND to enable all four accelerators. Float ACC to enable
the SDAOUT and SCLOUT accelerators only. For applica-
tions when V
CC
 is greater than the bus pull-up voltage,
connect ACC to V
CC
.
GND (Pin 5): Device Ground. Connect this pin to a ground 
plane for best results.
READY (Pin 6): Connection Status Flag. READY provides 
a digital  ag which indicates the status of the connection
circuitry described in the Connection Circuitry section.
Connect a resistor of 10k to V
CC
 to provide the pull-up.
FAULT (Pin 7): Bus Stuck Low Fault. FAULT is an open 
drain N-channel MOSFET which pulls low to signal a bus
stuck low condition. In normal operation, FAULT is high.
Connect a 10k resistor from this pin to V
CC
 to provide
the pull-up.
SDAIN (Pin 8): Serial Data Input. Connect this pin to the 
SDA bus on the backplane.
SDAOUT (Pin 9): Serial Data Output. Connect this pin to 
the SDA bus on the card.
V
CC
 (Pin 10): Supply Voltage Input. Place a bypass capaci-
tor of at least 0.01礔 close to V
CC
 for best results.
Exposed Pad (Pin 11, DFN Only): Exposed pad may be 
left open or connected to the ground plane.
PI  FU CTIO S
U
U
相關PDF資料
PDF描述
LTC4307IMS8-1#TRPBF IC BUFFER 2-WIRE BUS 8-MSOP
LTC4307IMS8#TRPBF IC BUS BUFFER I2C 8-MSOP
LTC4308IMS8#TRPBF IC BUS BUFFER LV 8-MSOP
LTC4309IGN#TRPBF IC BUS BUFFER 2-WIRE 16-SSOP
LTC4350IGN#PBF IC CTLR HOTSWAP LOADSHARE 16SSOP
相關代理商/技術參數
參數描述
LTC4304IMS#PBF 功能描述:IC BUS BUFFER I2C 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP(3x3) 包裝:管件
LTC4304IMS#TR 制造商:Linear Technology 功能描述:Hot Swappable Bus Buffer 10-Pin MSOP T/R
LTC4304IMS#TRPBF 功能描述:IC BUS BUFFER I2C 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP(3x3) 包裝:管件
LTC4305CDHD 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
LTC4305CDHD#PBF 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C,SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1