參數資料
型號： LTC4257CDD-1
廠商： LINEAR TECHNOLOGY CORP
元件分類： 電源管理
英文描述： Power over Ethernet Interface Controller with Dual Current Limit
中文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
封裝： 3 X 3 MM, PLASTIC, M0-229WEED-1, DFN-8
文件頁數： 4/32頁
文件大?。?/td> 1975K
代理商： LTC4257CDD-1
LTC4267
4
4267f
Note 1:
Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2:
P
VCC
internal clamp circuit self regulates to 9.4V with respect to
PGND.
Note 3:
The LTC4267 operates with a negative supply voltage in the range
of –1.5V to –57V. To avoid confusion, voltages for the PD interface
are always referred to in terms of absolute magnitude. Terms such as
“maximum negative voltage” refer to the largest negative voltage and
a “rising negative voltage” refers to a voltage that is becoming more
negative.
Note 4:
The LTC4267 is designed to work with two polarity protection
diode drops between the PSE and PD. Parameter ranges specified in the
Electrical Characteristics section are with respect to this product pins and
are designed to meet IEEE 802.3af specifications when these diode drops
are included. See the Application Information section.
Note 5:
Signature resistance is measured via the two-point
Δ
V/
Δ
I method
as defined by IEEE 802.3af. The PD signature resistance is offset from the
25k
Ω
to account for diode resistance. With two series diodes, the total PD
resistance will be between 23.75k
Ω
and 26.25k
Ω
and meet IEEE 802.3af
specifications. The minimum probe voltages measured at the LTC4267
pins are –1.5V and –2.5V. The maximum probe voltages are –8.5V and
–9.5V.
Note 6:
The PD interface includes hysteresis in the UVLO voltages to
preclude any start-up oscillation. Per IEEE 802.3af requirements, the PD
will power up from a voltage source with 20
Ω
series resistance on the first
trial.
Note 7:
Dynamic Supply current is higher due to the gate charge being
delivered at the switching frequency.
Note 8:
I
VPORTN_CLASS
does not include classification current
programmed at the R
CLASS
pin. Total current in classification mode will be
I
VPORTN_CLASS
+ I
CLASS
(See note 9).
Note 9:
I
CLASS
is the measured current flowing through R
CLASS
.
Δ
I
CLASS
accuracy is with respect to the ideal current defined as I
CLASS
= 1.237/
R
CLASS
. The current accuracy does not include variations in R
CLASS
resistance. The total classification current for a PD also includes the IC
quiescent current (I
VPORTN_CLASS
). See Applications Information.
Note 10:
For the DHC package, this parameter is assured by design and
wafer level testing.
Note 11:
To disable the 25k
Ω
signature, tie SIGDISA to V
PORTP
or hold
SIGDISA high with respect to V
PORTN
. See Applications Information.
Note 12:
The switching regulator is tested in a feedback loop that servos
V
FB
to the output of the error amplifier while maintaining I
TH
/RUN at the
midpoint of the current limit range.
Note 13:
I
POUT_LEAK
includes current drawn through P
OUT
by the power
good status circuit. This current is compensated for in the 25k
Ω
signature
resistance and does not affect PD operation.
Note 14:
The LTC4267 PD Interface includes thermal protection. In the
event of an overtemperature condition, the PD interface will turn off
the switching regulator until the part cools below the overtemperature
limit. The LTC4267 is also protected against thermal damage from
incorrect classification probing by the PSE. If the LTC4267 exceeds the
overtemperature threshold, the classification load current is disabled.
Note 15:
The PD interface includes dual level input current limit. At turn-
on, before the P
OUT
load capacitor is charged, the PD current level is set
to a low level. After the load capacitor is charged and the P
OUT
– V
PORTN
voltage difference is below the power good threshold, the PD switches to
high level current limit. The PD stays in high level current limit until the
input voltage drops below the UVLO turn-off threshold.
Note 16:
Peak current sense voltage is reduced dependent on duty cycle
and an optional external resistor in series with the SENSE pin (R
SL
). For
details, refer to the programmable slope compensation feature in the
Applications Information section.
Note 17:
Guaranteed by design.
Note 18:
The PD interface includes overtemperature protection that is
intended to protect the device from momentary overload conditions.
Junction temperature will exceed 125°C when overtemperature protection
is active. Continuous operation above the specified maximum operating
junction temperature may impair device reliability.
ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifications are at T
A
= 25°C. (Note 3)
SYMBOL
PARAMETER
t
RISE
NGATE Drive Rise Time
t
FALL
NGATE Drive Fall Time
V
IMAX
Peak Current Sense Voltage
I
SLMAX
Peak Slope Compensation Output Current
t
SFST
Soft-Start Time
T
SHUTDOWN
Thermal Shutdown Trip Temperature
The
●
denotes the specifications which apply over the full operating
CONDITIONS
C
LOAD
= 3000pF, P
VCC
– P
GND
= 8V
C
LOAD
= 3000pF, P
VCC
– P
GND
= 8V
R
SL
= 0, P
VCC
– P
GND
= 8V (Note 16)
P
VCC
– P
GND
= 8V (Note 17)
P
VCC
– P
GND
= 8V
(Notes 14, 18)
MIN
90
TYP
40
40
100
5
1.4
140
MAX
115
UNITS
ns
ns
mV
μA
ms
°C
●
相關PDF資料
PDF描述
LTC4267 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4267IDHC RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4267IGN RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4267CGN RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC4259A Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect
相關代理商/技術參數
參數描述
LTC4257CDD-1#PBF 功能描述:IC CONTROLLER POE INTERFACE 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4257CDD-1#TR 功能描述:IC CONTROLLER POE INTERFACE 8DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4257CDD-1#TRPBF 功能描述:IC CONTROLLER POE INTERFACE 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4257CS8 功能描述:IC CTRLR INTFACE PWR/ETHER 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4257CS8-#1TRPBF 制造商:LINEAR_TECH 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*