- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4251-2CS6#TRPBF (Linear Technology)IC CTRLR HOTSWAP NEGVOLT SOT23-6 Datasheet資料下載
參數資料
| 型號： | LTC4251-2CS6#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 266K |
| 描述： | IC CTRLR HOTSWAP NEGVOLT SOT23-6 |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | -43V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 細型，TSOT-23-6 |
| 供應商設備封裝： | SOT-23-6 |
| 包裝： | 帶卷 (TR) |
13
425112fd
LTC4251/LTC4251-1/
LTC4251-2
For more information www.linear.com/4251
SENSE
The SENSE pin is monitored by the circuit breaker (CB)
comparator, the analog current limit (ACL) amplifier, and
the fast current limit (FCL) comparator. Each of these
three measures the potential of SENSE relative to V
EE
. If
SENSE exceeds 50mV , the CB comparator activates the
230礎 TIMER pull-up. At 100mV , the ACL amplifier servos
the MOSFET current, and at 200mV the FCL compara-
tor abruptly pulls GATE low in an attempt to bring the
MOSFET current under control. If any of these conditions
persists long enough for TIMER to charge C
T
to 4V (see
Equation?2)), the LTC4251/LTC4251-1/LTC4251-2 latch
off and pull GATE low.
If the SENSE pin encounters a voltage greater than 100mV ,
the ACL amplifier will servo GATE downwards in an attempt
to control the MOSFET current. Since GATE overdrives the
MOSFET in normal operation, the ACL amplifier needs time
to discharge GATE to the threshold of the MOSFET . For a
mild overload, the ACL amplifier can control the MOSFET
current, but in the event of a severe overload the current
may overshoot. At SENSE = 200mV , the FCL comparator
takes over, quickly discharging the GATE pin to near V
EE
potential. FCL then releases, and the ACL amplifier takes
over. All the while TIMER is running. The effect of FCL is
to add a nonlinear response to the control loop in favor
of reducing MOSFET current.
Owing to inductive effects in the system, FCL typically
overcorrects the current limit loop, and GATE undershoots.
A zero in the loop (resistor R
C
in series with the gate
capacitor) helps the ACL amplifier recover.
SHORT-CIRCUIT OPERATION
Circuit behavior arising from a load-side low impedance
short is shown in Figure 4. Initially, the current overshoots
the analog current limit level of V
SENSE
= 100mV (Trace 2)
as the GATE pin works to bring V
GS
under control (Trace?).
The overshoot glitches the backplane in the negative
direction, and when the current is reduced to 100mV/R
S
the backplane responds by glitching in the positive
direction.
TIMER commences charging C
T
(Trace 4) while the
analog current limit loop maintains the fault current at
100mV/R
S
, which in this case is 5A (Trace 2). Note that
the backplane voltage (Trace 1) sags under load. When C
T
reaches 4V , GATE turns off, the load current drops to zero
and the backplane rings up to over 100V . The positive peak
is usually limited by avalanche breakdown in the MOSFET ,
and can be further limited by adding a transient voltage
suppressor across the input from 48V to 48RTN, such
as Diodes Inc. SMAT70A.
A low impedance short on one card may influence the
behavior of others sharing the same backplane. The initial
glitch and backplane sag as seen in Figure 4, Trace 1, can
rob charge from output capacitors on adjacent cards. When
the faulty card shuts down, current flows in to refresh the
capacitors. If LTC4251, LTC4251-1 or LTC4251-2s are used
throughout, they respond by limiting the inrush current to
a value of 100mV/R
S
. If C
T
is sized correctly, the capacitors
will recharge long before C
T
times out.
APPLICATIONS INFORMATION
MOSFET SELECTION
The external MOSFET switch must have adequate safe
operating area (SOA) to charge the load capacitance on
start-up and handle short-circuit conditions until TIMER
latchoff. These considerations take precedence over DC
current ratings. A MOSFET with adequate SOA for a given
application can always handle the required current, but
the opposite cannot be said. Consult the manufacturers
MOSFET data sheet for safe operating area and effective
transient thermal impedance curves.
Figure 4. Output Short-Circuit Behavior
(All Waveforms are Referenced to V
EE)
GATE
10V/DIV
SENSE
200mV/DIV
48RTN
50V/DIV
TIMER
5V/DIV
425112 F04
SUPPLY RING
OWING
TO CURRENT
OVERSHOOT
SUPPLY RING
OWING TO
MOSFET
TURN-OFF
ONSET OF OUTPUT
SHORT-CIRCUIT
FAST CURRENT
LIMIT
ANALOG
CURRENT LIMIT
C
TIMER
RAMP
LATCH OFF
TRACE 1
TRACE 2
TRACE 3
TRACE 4
2ms/DIV
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4252A-1IMS#TRPBF | IC CNTRLR HOTSWAP NEGVOLT 10MSOP |
| LTC4253ACGN#TRPBF | IC HOT SWAP CONTRLR -48V 16-SSOP |
| LTC4257CS8 | IC CTRLR INTFACE PWR/ETHER 8SOIC |
| LTC4260IUH#PBF | IC HOT SWAP CNTRL I2C 32-QFN |
| LTC4261IGN-2#PBF | IC CTRLR HOTSWAP W/ADC 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4251-2IS6 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers in SOT-23 |
| LTC4251-2IS6#TR | 功能描述:IC CTRLR HOTSWP NEG VOLT SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4251-2IS6#TRM | 功能描述:IC CTRLR HOTSWP NEG VOLT SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4251-2IS6#TRMPBF | 功能描述:IC CTRLR HOTSWAP NEGVOLT SOT23-6 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4251-2IS6#TRPBF | 功能描述:IC CTRLR HOTSWAP NEGVOLT SOT23-6 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。