- 您現在的位置：買賣IC網 > PDF目錄377778 > LTC4244IGN-1 (LINEAR TECHNOLOGY CORP) Rugged, CompactPCI Bus Hot Swap Controllers PDF資料下載
參數資料
| 型號： | LTC4244IGN-1 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Rugged, CompactPCI Bus Hot Swap Controllers |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-20 |
| 文件頁數： | 8/28頁 |
| 文件大小： | 333K |
| 代理商： | LTC4244IGN-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
8
LTC4244/LTC4244-1
42441f
RESETOUT (Pin 10):
Open-Drain Digital Output. Connect
the CPCI_LOCAL_RST# signal to the RESETOUT pin.
RESETOUT is the logical combination of the RESETIN and
PWRGD.
DRIVE (Pin 11):
Precharge Base Drive Output. Provides
base drive for an external NPN emitter-follower that in turn
biases the PRECHARGE node.
PRECHARGE (Pin 12):
Precharge Monitor Input. An inter-
nal error amplifier servos the DRIVE pin voltage to keep the
PRECHARGE node at 1V. See Applications Information for
generating voltages other than 1V. If not used, tie the
PRECHARGE pin to ground.
5V
IN
(Pin 13):
5V Supply Sense Input. An undervoltage
lockout circuit prevents the switches from turning on
when the voltage at the 5V
IN
pin is less than 4.25V.
5V
SENSE
(Pin 14):
5V Current Limit Sense. With a sense
resistor placed in the supply path between 5V
IN
and
5V
SENSE
, the GATE pin voltage will be adjusted to maintain
a constant 51mV across the sense resistor and a constant
current through the switch while the TIMER pin is low. A
foldback feature makes the current limit decrease as the
voltage at the 5V
OUT
pin approaches GND. When the
TIMER pin is high, the circuit breaker function is enabled.
If the voltage across the sense resistor exceeds 52mV, the
circuit breaker is tripped after a 25
μ
s time delay. In the
event of a short-circuit or large overcurrent transient
condition, the GATE pin voltage will be adjusted to main-
tain a constant 150mV across the sense resistor and a
constant current through the switch.
GATE (Pin 15):
High Side Gate Drive for the External 3.3V
and 5V N-Channel Pass Transistors. An external series RC
network is required for current limit loop compensation
and setting the minimum ramp-up time. During power-up,
the slope of the voltage rise at the GATE is set by the 67
μ
A
current source connected through a Schottky diode to
12V
IN
and the external capacitor connected to GND (C1 in
Figure 1) or by the 3.3V or 5V current limit and the bulk
capacitance in the 3.3V
OUT
or 5V
OUT
supply lines. During
power down, the slew rate of the GATE voltage is set by the
60
μ
A current source connected to GND and the external
GATE capacitor (C1 in Figure 1).
The voltage at the GATE pin will be modulated to maintain
a constant current when either the 5V or 3.3V supplies go
into current limit. In the event of an overcurrent fault, the
GATE pin is immediately pulled to GND.
3.3V
SENSE
(Pin 16):
3.3V Current Limit Sense. With a
sense resistor placed in the supply path between 3.3V
IN
and 3.3V
SENSE
, the GATE pin voltage will be adjusted to
maintain a constant 51mV across the sense resistor and a
constant current through the switch while the TIMER pin
is low. A foldback feature makes the current limit decrease
as the voltage at the 3.3V
OUT
pin approaches GND. When
the TIMER pin is high, the circuit breaker function is
enabled. If the voltage across the sense resistor exceeds
52mV, the circuit breaker is tripped after a 25
μ
s time delay.
In the event of a short-circuit or large overcurrent transient
condition, the GATE pin voltage will be adjusted to main-
tain a constant 150mV across the sense resistor and a
constant current through the switch.
If no 3.3V input supply is available, short the 3.3V
SENSE
pin
to the 5V
IN
pin.
PU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4244CGN | Rugged, CompactPCI Bus Hot Swap Controllers |
| LTC4252-1 | TRANS ARRAY NPN/PNP SS MINI-6P |
| LTC4252 | Negative 48V Hot Swap Controller |
| LTC4252-1CMS | TRANS ARRAY PNP/PNP SS MINI-6P |
| LTC4252-1CMS8 | TRANS ARRAY NPN/NPN SSMINI-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4244IGN-1#PBF | 功能描述:IC CTLR HOT SWAP PCI 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4244IGN-1#TR | 功能描述:IC CTRLR HOT SWAP CPCI 20-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4244IGN-1#TRPBF | 功能描述:IC CTRLR HOTSWAP PCI 20-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4244IGNTR | 制造商:Linear Technology 功能描述: |
| LTC4245 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
發布緊急采購，3分鐘左右您將得到回復。