- 您現在的位置：買賣IC網 > PDF目錄377777 > LTC4240IGN (LINEAR TECHNOLOGY CORP) CompactPCI Hot Swap Controller with I2C Compatible Interface PDF資料下載
參數資料
| 型號： | LTC4240IGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | CompactPCI Hot Swap Controller with I2C Compatible Interface |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP28 |
| 文件頁數： | 15/28頁 |
| 文件大小： | 486K |
| 代理商： | LTC4240IGN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4240
15
4240f
Table 3 shows the definition for each data bit. PWRGD,
FAULT, RESETIN, and RESETOUT external pins can be
monitored. PRSNT1# and PRSNT2# are PCI signals that
provide information on the power requirements of the
board. Refer to PCI local bus specifications for a detailed
description. FAULTCODE1 and FAULTCODE0 are two in-
ternal binary encoded signals that, along with FAULT,
indicate which of the four supplies generated a fault. Note
that the FAULTCODE signals are valid only when FAULT
has been asserted low. See Table 4 for description.
Status LED
The main function of the LED is to alert the user when it is
permissible to physically extract the board. The LED
output of the LTC4240 is an open drain N-channel device
capable of sinking 10mA from an externally connected
LED. This LED lights up when RESETOUT
(LOCAL_PCI_RST#) is asserted. Upon application of Early
Power, the long 5V pins will power up the LTC4240 and
light up the Status LED. It will remain on until PWRGD
(HEALTHY#) is asserted and RESETIN (PCI_RST#) is de-
asserted, and the board enters normal operation. Note that
this LED can also be turned on via the I
2
C 2-wire interface.
CPCI Connection Pin Sequence
The staggered length of the CPCI male connector pins
ensures that all power supplies are physically connected
APPLICATIOU
W
U
U
Table 3. STATUS Byte Definitions
S7
S6
S5
S4
S3
S2
S1
S0
Logic state of the PRSNT2# pin
Logic state of the PRSNT1# pin
Logic state of the PWRGD pin
Logic state of the RESETOUT pin
Logic state of the RESETIN pin
FAULTCODE1 (see Table 4)
FAULTCODE0 (see Table 4)
Logic state of the FAULT pin
Table 4. FAULTCODE Encoding Description for Receive Byte
FAULTCODE0
FAULTCODE1
LO
LO
LO
HI
HI
LO
HI
HI
X
X
FAULT
LO
LO
LO
LO
HI
Supply Causing Fault
3V
IN
5V
IN
12V
IN
V
EEIN
None
SCL
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
STOP
SDA
START
ACK
ACK
R/WR=1
ADDR 4
ADDR 3
ADDR 2
ADDR 1
ADDR 0
S5
S4
S3
S2
S1
S0
0
1
S7
S6
ADDRESS BYTE
DATA BYTE
4240 F03
Figure 3. Receive Byte Protocol
to the LTC4240 before back-end power is allowed to ramp
(BD_SEL# asserted low). The long pins, which include 5V,
3.3V, V(I/O) and GND mate first. The short pins, which
includes BD_SEL# (OFF/ON), mate last. At least one long
5V power pin must be connected to the LTC4240 in order
for the PRECHARGE voltage to be available during Early
Power. The external components connected to the
precharge pin require long 3.3V.
The following is a typical hot plug sequence:
1. ESD clips make contact.
2. Long power and ground pins make contact and Early
Power is established (see Early Power section). The 1V
PRECHARGE voltage becomes valid at this stage. Power
is applied to the pull-up resistors connected to FAULT,
PWRGD and OFF/ON pins. The status LED is lit, indicat-
ing that the plug-in board is in the process of being
connected (LOCAL_PCI_RST# is asserted). All power
switches are off.
3. Medium length pins make contact. There are six 5V and
eight 3.3V medium length power pins, bringing the 5V
total to 8 pins and the 3.3V total to 10 pins. The
maximum DC current for the 3.3V and 5V supplies is
10A and 8A, respectively. The I
2
C command latch is
initialized to allow seamless CPCI Hot Swap operation.
The LTC4240 can be used as a Hot Swap controller
without ever establishing I
2
C communication. Both
FAULT and PWRGD continue to be pulled up high at this
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4240CGN | CompactPCI Hot Swap Controller with I2C Compatible Interface |
| LTC4244 | Rugged, CompactPCI Bus Hot Swap Controllers |
| LTC4244CGN-1 | Rugged, CompactPCI Bus Hot Swap Controllers |
| LTC4244IGN | Rugged, CompactPCI Bus Hot Swap Controllers |
| LTC4244IGN-1 | Rugged, CompactPCI Bus Hot Swap Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4240IGN#PBF | 功能描述:IC CTRLR HOTSWAP CPCI I2C 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4240IGN#TR | 功能描述:IC CTRLR HOT SWAP CPCI 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4240IGN#TRPBF | 功能描述:IC CTRLR HOTSWAP CPCI I2C 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4241 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:PCI-Bus with 3.3V Auxiliary Hot Swap Controller |
| LTC4241CGN | 功能描述:IC CTRLR HOTSWAP PCI 3.3V 20SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。