參數資料
型號： LTC4215IUFD#PBF
廠商： Linear Technology
文件頁數： 19/28頁
文件大?。?/td> 265K
描述： IC CNTRLR HOT SWAP 24-QFN
標準包裝： 73
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： 2.9 V ~ 15 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-WFQFN 裸露焊盤
供應商設備封裝： 24-QFN（5x4）
包裝： 管件
LTC4215/LTC4215-2
19
4215fe
 APPLICATIONS INFORMATION
SCL
SDA
START
CONDITION
STOP
CONDITION
ADDRESS
R/W
ACK
DATA
ACK
DATA
ACK
1 - 7
8
9
4215 F06
a6 - a0
b7 - b0
b7 - b0
1 - 7
8
9
1 - 7
8
9
P
S
Figure 6. Data Transfer Over I
2
C or SMBus
Digital Interface
The LTC4215 communicates with a bus master using a
2-wire interface compatible with I
2
C Bus and SMBus, an
I
2
C extension for low power devices.
The LTC4215 is a read-write slave device and supports
SMBus bus Read Byte, Write Byte, Read Word and Write
Word commands. The second word in a Read Word com-
mand is identical to the  rst word. The second word in a
Write Word command is ignored. Data formats for these
commands are shown in Figures 6 to 11.
START and STOP Conditions
When the bus is idle, both SCL and SDA are high. A bus
master signals the beginning of a transmission with a start
condition by transitioning SDA from high to low while SCL
is high, as shown in Figure 6. When the master has  nished
communicating with the slave, it issues a STOP condition
by transitioning SDA from low to high while SCL is high.
The bus is then free for another transmission.
I
2
C Device Addressing
Twenty-seven distinct bus addresses are available using
three 3-state address pins, ADR0-ADR2. Table 1 shows
the correspondence between pin states and addresses.
Note that address bits B7 and B6 are internally con gured
to 10. In addition, the LTC4215 responds to two special
addresses. Address (1011 111) is a mass write address
that writes to all LTC4215s, regardless of their individual
address settings. Mass write can be disabled by setting
register A4 to zero. Address (0001 100) is the SMBus Alert
Response Address. If the LTC4215 is pulling low on the
ALERT pin, it acknowledges this address by broadcasting
its address and releasing the ALERT pin.
Acknowledge
The acknowledge signal is used in handshaking between
transmitter and receiver to indicate that the last byte of
data was received. The transmitter always releases the
SDA line during the acknowledge clock pulse. When the
slave is the receiver, it pulls down the SDA line so that it
remains LOW during this pulse to acknowledge receipt
of the data. If the slave fails to acknowledge by leaving
SDA high, then the master may abort the transmission by
generating a STOP condition. When the master is receiving
data from the slave, the master pulls down the SDA line
during the clock pulse to indicate receipt of the data. After
the last byte has been received the master leaves the SDA
line HIGH (not acknowledge) and issues a stop condition
to terminate the transmission.
Write Protocol
The master begins communication with a START con-
dition followed by the seven bit slave address and the
R/W bit set to zero, as shown in Figure 7. The addressed
LTC4215 acknowledges this and then the master sends
a command byte which indicates which internal register
the master wishes to write. The LTC4215 acknowledges
this and then latches the lower three bits of the command
byte into its internal Register Address pointer. The master
then delivers the data byte and the LTC4215 acknowledges
once more and latches the data into its control register.
相關PDF資料
PDF描述
LTC4216IDE#TRPBF IC CNTRLR HOT SWAP 12-DFN
LTC4221IGN#TRPBF IC CTRLR HOTSWAP DUAL 16SSOP
LTC4222CG#PBF IC CTRLR DUAL HOT SWAP 36-SSOP
LTC4223CDHD-2#PBF IC CNTRLR HOT SWAP DUAL 16-DFN
LTC4224IDDB-2#TRPBF IC CNTRLR HOT SWAP DUAL 10-DFN
相關代理商/技術參數
參數描述
LTC4216 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller
LTC4216CDE 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 6V 12-Pin DFN EP
LTC4216CDE#PBF 功能描述:IC CTLR HOT SWAP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
LTC4216CDE#TR 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 6V 12-Pin DFN EP T/R
LTC4216CDE#TRPBF 功能描述:IC CNTRLR HOT SWAP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*