- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4211IMS8 (Linear Technology)IC CONTROLLER HOT SWAP 8-MSOP Datasheet資料下載
參數資料
| 型號： | LTC4211IMS8 |
| 廠商： | Linear Technology |
| 文件頁數： | 24/40頁 |
| 文件大?。?/td> | 321K |
| 描述： | IC CONTROLLER HOT SWAP 8-MSOP |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.5 V ~ 16.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC4211
24
4211fb
OPERATION
R
DS(ON)
. Table 5 lists some power MOSFETs that can be
used with the LTC4211.
For reliable circuit operation, the maximum junction
temperature (T
J(MAX)
) for a power MOSFET should not
exceed the manufacturers recommended value. This
includes normal mode operation, start-up, current-limit
and autoretry mode in a fault condition. Under normal
conditions the junction temperature of a power MOSFET
is given by Equation 13:
MOSFET Junction Temperature,
T
J(MAX)
d T
A(MAX)
+ ?/DIV>
JA
" P
D
(13)
where
P
D
= (I
LOAD
)
2
" R
DS(ON)
?/DIV>
JA
= junction-to-ambient thermal resistance
T
A(MAX)
= maximum ambient temperature
If a short circuit happens during start-up, the external
MOSFET can experience a big single pulse energy. This
is especially true if the applications only employ a small
gate capacitor or no gate capacitor at all. Consult the safe
operating area (SOA) curve of the selected MOSFET to
ensure that the T
J(MAX)
is not exceeded during start-up.
USING STAGGERED PIN CONNECTORS
The LTC4211 can be used on either a printed circuit board
or on the backplane side of the connector, and examples
for both are shown in Figures 13 and 14. Printed circuit
board edge connectors with staggered pins are recom-
mended as the insertion and removal of circuit boards do
sequence the pin connections. Supply voltage and ground
connections on the printed circuit board should be wired
to the edge connectors long pins or blades. Control and
status signals (like RESET, FAULT and ON) passing through
the cards edge connector should be wired to short length
pins or blades.
PCB CONNECTION SENSE
There are a number of ways to use the LTC4211s ON pin
to detect whether the printed circuit board has been fully
seated in the backplane before the LTC4211 commences
a start-up cycle.
The first example is shown in the schematic on the front
page of this data sheet. In this case, the LTC4211 is
mounted on the PCB and a 20k/10k resistive divider is
connected to the ON pin. On the edge connector, R1 is
wired to a short pin. Until the connectors are fully mated,
the ON pin is held low, keeping the LTC4211 in an OFF
state. Once the connectors are mated, the resistive divider
is connected to V
CC
, V
ON
> 1.316V and the LTC4211 begins
a start-up cycle.
In Figure 13, an LTC4211 is illustrated in a basic configura-
tion on a PCB daughter card. The ON pin is connected to
V
CC
on the backplane through a 10k pull-up resistor once
the card is seated into the backplane. R2 bleeds off any
potential static charge which might exist on the backplane,
the connector or during card installation.
A third example is shown in Figure 14 where the LTC4211
is mounted on the backplane. In this example, a 2N2222
transistor and a pair of resistors (R4, R5) form the PCB
connection sense circuit. With the card out of the chassis,
Q2s base is biased to V
CC
through R5, biasing Q2 ON
and driving the LTC4211s ON pin low. The base of Q2 is
also wired to a socket on the backplane connector. When
a card is firmly seated into the backplane, the base of Q2
is then grounded through a short pin connection on the
card. Q2 is biased OFF, the LTC4211s ON pin is pulled-up
to V
CC
and a start-up cycle begins.
In the previous three examples, the connection sense was
hard wired with no processor (low) interrupt capability.
As illustrated in Figure 15, the addition of an inexpensive
logic-level discrete MOSFET and a couple of resistors offers
processor interrupt control to the connection sense. R4
keeps the gate of M2 at V
CC
until the card is firmly mated
to the backplane. A logic low for the ON/OFF signal turns
M2 OFF, allows the ON pin to pull high and turns on the
LTC4211.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4212IMS#TRPBF | IC CTRLR HOTSWAP TIMEOUT 10MSOP |
| LTC4214-1IMS#TRPBF | IC CTRLR HOTSWAP NEGVOLT 10MSOP |
| LTC4215IUFD#PBF | IC CNTRLR HOT SWAP 24-QFN |
| LTC4216IDE#TRPBF | IC CNTRLR HOT SWAP 12-DFN |
| LTC4221IGN#TRPBF | IC CTRLR HOTSWAP DUAL 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4211IMS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4211IMS8#TR | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IMS8#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IS8 | 功能描述:IC CTRLR HOTSWAP CURR CTRL 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4211IS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。