- 您現在的位置：買賣IC網 > PDF目錄377776 > LTC4063 (Linear Technology Corporation) Standalone Linear Li-lon Battery Charger with Thermistor Input PDF資料下載
參數資料
| 型號： | LTC4063 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 熱敏電阻 |
| 英文描述： | Standalone Linear Li-lon Battery Charger with Thermistor Input |
| 中文描述： | 獨立線性鋰離子電池充電器熱敏電阻輸入 |
| 文件頁數： | 7/20頁 |
| 文件大小： | 665K |
| 代理商： | LTC4063 |
LTC4061
7
4061fa
BAT (Pin 1):
Charge Current Output. This pin provides
charge current to the battery and regulates the final float
voltage to 4.2V.
NTC (Pin 2):
Input to the NTC (Negative Temperature Coef-
ficient) Thermistor Temperature Monitoring Circuit. Under
normal operation, connect a thermistor from the NTC pin
to ground and a resistor of equal value from the NTC pin
to V
CC
. When the voltage at this pin drops below 0.35
V
CC
at hot temperatures or rises above 0.76 V
CC
at cold,
charging is suspended, the internal timer is frozen and the
C
H
R
G pin output will start to pulse at 1.5Hz. Pulling this
pin below 0.016 V
CC
disables the NTC feature. There is
approximately 2°C of temperature hysteresis associated
with each of the input comparators thresholds.
TIMER (Pin 3):
Timer Program and Termination Select Pin.
This pin selects which method is used to terminate the
charge cycle. Connecting a capacitor, C
TIMER
, to ground
selects charge time termination. The charge time is set
by the following formula:
TIME HOURS
(
HOURS
C
F
or
C
F
TIME HOURS
HOURS
(
3
TIMER
.
)
TIMER
)
.
(
)
=
μ
=
μ
3
0 1
0 1
Connecting the TIMER pin to ground selects charge cur-
rent termination, while connecting the pin to V
CC
selects
user termination. See Applications Information for more
information on current and user termination.
ACPR (Pin 4):
Open-Drain Power Supply Present Status
Output. The power supply status indicator pin has two
states: pull-down and high impedance. This output can
be used as a logic interface or as a LED driver. In the
pull-down state, an NMOS transistor capable of sinking
10mA pulls down on the
A
C
P
R pin. The state of this pin
is dependent on the value of V
CC
and BAT: it requires that
V
CC
is 190mV greater than V
BAT
and greater than V
UVLO
.
See Applications Information.
C
H
R
G (Pin 5):
Open-Drain Charge Status Output. The
charge status indicator pin has three states: pull-down,
PIU
pulse at 1.5Hz or 6Hz and high impedance. This output
can be used as a logic interface or as a LED driver. In the
pull-down state, an NMOS transistor capable of sinking
10mA pulls down on the
C
H
R
G pin. The state of this pin
depends on the value of I
DETECT
as well as the termina-
tion method being used and the state of the NTC pin. See
Applications Information.
C
/
5 (Pin 6):
C
/
5 Enable Input. Used to control the amount
of current drawn from the USB port. A logic high on the
C
/
5 pin sets the current limit to 100% of the current
programmed by the PROG pin. A logic low on the
C
/
5 pin
sets the current limit to 20% of the current programmed
by the PROG pin. An internal 3M
Ω
pull-down resistor
defaults the
C
/
5 pin to its low current state.
E
N (Pin 7):
Charger Enable Input. A logic high on the
E
N pin
places the charger into shutdown mode, where the input
quiescent current is less than 50μA. A logic low on this
pin enables charging. An internal 3M
Ω
pull-down resistor
to ground defaults the charger to its enabled state.
I
DET
(Pin 8)
: Current Detection Threshold Program Pin.
The current detection threshold, I
DETECT
, is set by con-
necting a resistor, R
DETECT
, to ground. I
DETECT
is set by
the following formula:
I
R
10
100
R
V
I
V
R
or
R
I
DETECT
PROG
DET
CHG
DET
DET
DETECT
=
=
=
100
The
C
H
R
G pin becomes high impedance when the charge
current drops below I
DETECT
. I
DETECT
can be set to 1/10th
the programmed charge current by connecting I
DET
di-
rectly to PROG. If the I
DET
pin is not connected, the
C
H
R
G
output remains in its pull-down state until the charge time
elapses and terminates the charge cycle. See Applications
Information.
This pin is clamped to approximately 2.4V. Driving this pin to
voltages beyond the clamp voltage should be avoided.
PROG (Pin 9):
Charge Current Program and Charge Cur-
rent Monitor. The charge current is set by connecting a
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4053EMSE-4.2 | USB Compatible Lithium-Ion Battery Charger with Thermal Regulation |
| LTC4002ES8-4.2 | Standalone Li-Ion Switch Mode Battery Charger |
| LTC4007 | 4A, High Efficiency, Standalone Li Battery Charger |
| LTC4006 | 4A, High Efficiency, Standalone Li Battery Charger |
| LTC4006EGN-2 | 4A, High Efficiency, Standalone Li-Ion Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4063EDD | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4063EDD#PBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監(jiān)控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4063EDD#TRPBF | 功能描述:IC BATT CHRGR LI-ION LDO 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4064 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic Linear Charger for Back-Up Li-Ion Batteries |
| LTC4064EMSE | 功能描述:IC CHARGER BATT L-ION 4V 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發(fā)布緊急采購，3分鐘左右您將得到回復。