- 您現在的位置：買賣IC網 > PDF目錄224115 > LTC4053EDD-4.2#PBF (LINEAR TECHNOLOGY CORP) USB Compatible Lithium-Ion Battery Charger with Thermal Regulation; Package: DFN; No of Pins: 10; Temperature Range: -40°C to +125°C PDF資料下載
參數資料
| 型號： | LTC4053EDD-4.2#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | USB Compatible Lithium-Ion Battery Charger with Thermal Regulation; Package: DFN; No of Pins: 10; Temperature Range: -40°C to +125°C |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, DFN-10 |
| 文件頁數： | 2/16頁 |
| 文件大小： | 199K |
| 代理商： | LTC4053EDD-4.2#PBF |
LTC4053-4.2
10
4053fa
Programming The Timer
The programmable timer is used to terminate the charge
cycle. The timer duration is programmed by an external
capacitor at the TIMER pin. The total charge time is:
Time (Hours) = (3 Hours) (CTIMER/0.1F) or
CTIMER = 0.1F Time (Hours)/3 (Hours)
The timer starts when an input voltage greater than the
undervoltage lockout threshold level is applied and the
SHDN pin is greater than the manual shutdown threshold
voltage level. After a time-out occurs, the charge current
stops, and the CHRG output assumes a high impedance
state to indicate that the charging has stopped. Connect-
ing the TIMER pin to ground disables the timer function.
Recharge
After a charge cycle has terminated, if the battery voltage
drops below the recharge threshold of 4.05V a new charge
cycle will begin. The recharge circuit integrates the BAT
pin voltage for a few milliseconds to prevent a transient
from restarting the charge cycle.
If the battery voltage remains below 2.48V during trickle
charge for 1/4 of the programmed time, the battery may be
defective and the charge cycle will end. In addition, the
recharge comparator is disabled and a new charge cycle
will not begin unless the input voltage is toggled off-then-
on, the SHDN pin is momentarily pulled to ground, or the
BAT pin is pulled above the 2.48V trickle charge threshold.
Open-Drain Status Outputs
The LTC4053 has three open-drain status outputs: ACPR,
CHRG and FAULT. The ACPR pin pulls low when an input
voltage greater than the undervoltage lockout threshold is
applied and becomes high impedance when power (VIN <
VUV) is removed. CHRG and FAULT work together to
indicate the status of the charge cycle. Table 1 describes
the status of the charge cycle based on the CHRG and
FAULT outputs.
APPLICATIO S I FOR ATIO
WU
UU
Table 1.
FAULT
CHRG
Description
High
Low
Charge cycle has started, C/10 has not been
reached and charging is proceeding normally.
Low
Charge cycle has started, C/10 has not been
reached, but the charge current and timer
have been paused due to an NTC out-of-
temperature condition.
High
30
A
C/10 has been reached and charging is
pull-down
proceeding normally.
Low
30
A
C/10 has been reached but the charge current
pull-down
and timer have paused due to an NTC out-of-
temperature condition.
High
Normal timeout (charging has terminated).
Low
High
If FAULT goes low and CHRG goes high
impedance simultaneously, then the LTC4053
has timed out due to a bad cell (VBAT <2.48V
after one-quarter the programmed charge time).
If CHRG goes high impedance first, then
the LTC4053 has timed out normally (charging
has terminated), but NTC is indicating an out-
of-temperature condition.
CHRG Status Output Pin
When the charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET capable of
driving an LED. When the charge current drops to 10% of
the full-scale current (C/10), the N-channel MOSFET is
latched off and a weak 30
A current source to ground is
connected to the CHRG pin. After a time-out occurs,
the pin assumes a high impedance state. By using two
different value pull-up resistors a microprocessor can
detect three states from this pin (charging, C/10 and time-
out). See Figure 3.
When the LTC4053 is in charge mode, the CHRG pin is
pulled low by the internal N-channel MOSFET. To detect
this mode, force the digital output pin, OUT, high and
measure the voltage at the CHRG pin. The N-channel
MOSFET will pull the pin low even with the 2k pull-up
resistor. Once the charge current drops to 10% of the
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4053EMSE-4.2#PBF | USB Compatible Lithium-Ion Battery Charger with Thermal Regulation; Package: MSOP; No of Pins: 10; Temperature Range: -40°C to +125°C |
| LTC4053EMSE-4.2#TRPBF | USB Compatible Lithium-Ion Battery Charger with Thermal Regulation; Package: MSOP; No of Pins: 10; Temperature Range: -40°C to +125°C |
| LTC4054ES5-4.2#TRMPBF | Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT; Package: SOT; No of Pins: 5; Temperature Range: -40°C to +125°C |
| LTC4054ES5-4.2#TRPBF | Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT; Package: SOT; No of Pins: 5; Temperature Range: -40°C to +125°C |
| LTC4054XES5-4.2#TRMPBF | Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT; Package: SOT; No of Pins: 5; Temperature Range: -40°C to +125°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4053EMSE-4.2 | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4053EMSE-4.2#PBF | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監(jiān)控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4053EMSE-4.2#TR | 功能描述:IC BATT CHARGR LI-ION REG 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4053EMSE-4.2#TRPBF | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4054 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT |
發(fā)布緊急采購，3分鐘左右您將得到回復。