參數資料
型號： LTC4008EGN#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： 4A, High Efficiency, Multi-Chemistry Battery Charger; Package: SSOP; No of Pins: 20; Temperature Range: -40°C to +125°C
中文描述： BATTERY CHARGE CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO20
封裝： 0.150 INCH, LEAD FREE, PLASTIC, SSOP-20
文件頁數： 14/24頁
文件大?。?/td> 221K
代理商： LTC4008EGN#PBF
LTC4008
21
4008fb
APPLICATIONS INFORMATION
PCB Layout Considerations
For maximum efciency, the switch node rise and fall times
should be minimized. To prevent magnetic and electrical
eld radiation and high frequency resonant problems,
proper layout of the components connected to the IC is
essential. (See Figure 11.) Here is a PCB layout priority
list for proper layout. Layout the PCB using this specic
order.
1. Input capacitors need to be placed as close as possible
to switching FET’s supply and ground connections.
Shortest copper trace connections possible. These
parts must be on the same layer of copper. Vias must
not be used to make this connection.
2. The control IC needs to be close to the switching FET’s
gate terminals. Keep the gate drive signals short for
a clean FET drive. This includes IC supply pins that
connect to the switching FET source pins. The IC can
be placed on the opposite side of the PCB relative to
above.
3. Place inductor input as close as possible to switching
FET’s output connection. Minimize the surface area of
this trace. Make the trace width the minimum amount
needed to support current—no copper lls or pours.
Avoid running the connection using multiple layers in
parallel. Minimize capacitance from this node to any
other trace or plane.
4. Place the output current sense resistor right next to
the inductor output but oriented such that the IC’s
current sense feedback traces going to resistor are not
long. The feedback traces need to be routed together
as a single pair on the same layer at any given time
with smallest trace spacing possible. Locate any lter
component on these traces next to the IC and not at
the sense resistor location.
5. Place output capacitors next to the sense resistor
output and ground.
6. Output capacitor ground connections need to feed
into same copper that connects to the input capacitor
ground before tying back into system ground.
7. Connection of switching ground to system ground or
internal ground plane should be single point. If the
system has an internal system ground plane, a good
way to do this is to cluster vias into a single star point
to make the connection.
8. Route analog ground as a trace tied back to IC ground
(analog ground pin if present) before connecting to any
other ground. Avoid using the system ground plane.
CAD trick: make analog ground a separate ground net
and use a 0Ω resistor to tie analog ground to system
ground.
9. A good rule of thumb for via count for a given high
current path is to use 0.5A per via. Be consistent.
10. If possible, place all the parts listed above on the same
PCB layer.
11. Copper lls or pours are good for all power connections
except as noted above in Rule 3. You can also use
copper planes on multiple layers in parallel too—this
helps with thermal management and lower trace
inductance improving EMI performance further.
12. For best current programming accuracy provide a
Kelvin connection from RSENSE to CSP and BAT. See
Figure 12 as an example.
It is important to keep the parasitic capacitance on the RT,
CSP and BAT pins to a minimum. The traces connecting
these pins to their respective resistors should be as short
as possible.
相關PDF資料
PDF描述
LTC4008EGN#TRPBF 4A, High Efficiency, Multi-Chemistry Battery Charger; Package: SSOP; No of Pins: 20; Temperature Range: -40°C to +125°C
LTC4008EGN-1#PBF 4A, High Efficiency, Multi-Chemistry Battery Charger; Package: SSOP; No of Pins: 20; Temperature Range: -40°C to +125°C
LTC4008EGN-1#TRPBF 4A, High Efficiency, Multi-Chemistry Battery Charger; Package: SSOP; No of Pins: 20; Temperature Range: -40°C to +125°C
LTC4010CFE#PBF High Efficiency Standalone Nickel Battery Charger; Package: TSSOP; No of Pins: 16; Temperature Range: 0°C to +70°C
LTC4010CFE#TRPBF High Efficiency Standalone Nickel Battery Charger; Package: TSSOP; No of Pins: 16; Temperature Range: 0°C to +70°C
相關代理商/技術參數
參數描述
LTC4009 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage High Current Controller for Battery Charging and Power Management
LTC4009-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Effi ciency, Multi-Chemistry Battery Charger
LTC4009-2 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Effi ciency, Multi-Chemistry Battery Charger
LTC4009CUF#PBF 功能描述:IC CHARGER BATTERY MC 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2
LTC4009CUF#TRPBF 功能描述:IC CHARGER BATTERY MC 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*