- 您現在的位置：買賣IC網 > PDF目錄44993 > LTC3812EFE-5#TR (LINEAR TECHNOLOGY CORP) 1 A SWITCHING CONTROLLER, PDSO16 PDF資料下載
參數資料
| 型號： | LTC3812EFE-5#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1 A SWITCHING CONTROLLER, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, TSSOP-16 |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 425K |
| 代理商： | LTC3812EFE-5#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC3812-5
26
38125fb
FAULT CONDITIONS: CURRENT LIMIT AND FOLDBACK
The maximum inductor current is inherently limited in a
current mode controller by the maximum sense voltage. In
the LTC3812-5, the maximum sense voltage is controlled
by the voltage on the VRNG pin. With valley current control,
the maximum sense voltage and the sense resistance
determine the maximum allowed inductor valley current.
The corresponding output current limit is:
ILIMIT =
VSNS(MAX)
RDS(ON) T
+
1
2
IL
The current limit value should be checked to ensure that
ILIMIT(MIN) > IOUT(MAX). The minimum value of current limit
generally occurs with the largest VIN at the highest ambi-
ent temperature, conditions that cause the largest power
loss in the converter. Note that it is important to check for
self-consistency between the assumed MOSFET junction
temperature and the resulting value of ILIMIT which heats
the MOSFET switches.
Caution should be used when setting the current limit
based upon the RDS(ON) of the MOSFETs. The maximum
current limit is determined by the minimum MOSFET
on-resistance. Data sheets typically specify nominal
and maximum values for RDS(ON), but not a minimum.
A reasonable assumption is that the minimum RDS(ON)
lies the same percentage below the typical value as the
maximum lies above it. Consult the MOSFET manufacturer
for further guidelines.
To further limit current in the event of a short-circuit to
ground, the LTC3812-5 includes foldback current limiting.
If the output falls by more than 60%, then the maximum
sense voltage is progressively lowered to about one tenth
of its full value.
Be aware also that when the fault timeout is enabled for
the external NMOS regulator, an over current limit may
cause the output to fall below the minimum 4.5V UV
threshold. This condition will cause a linear regulator
timeout/restart sequence as described in the Linear Regula-
tor Timeout section if this condition persists.
RUN/SOFT-START FUNCTION
The RUN/SS pin is a multipurpose pin that provides a soft-
start function and a means to shut down the LTC3812-5.
Soft-start reduces the input supply’s surge current by
controlling the ramp rate of the output voltage, eliminates
output overshoot and can also be used for power supply
sequencing.
Pulling RUN/SS below 1.5V puts the LTC3812-5 into a low
quiescent current shutdown (IQ = 224μA). This pin can be
driven directly from logic as shown in Figure 14. Releasing
the RUN/SS pin allows an internal 1.4μA current source to
charge up the soft-start capacitor, CSS.Whenthevoltageon
RUN/SS reaches 1.5V, the LTC3812-5 turns on and begins
regulating the output to VFB = VSS – 1.5V. As the RUN/SS
voltage increases from 1.5V to 2.3V, the output voltage is
raised from 0% to 100% of its regulated value. Current
foldback, forced continuous mode and fault timeout are
disabled during this soft-start phase and PGOOD signal is
forced low. The RUN/SS voltage continues to charge until
it reaches its internally clamped value of 4V.
If RUN/SS starts at 0V, the delay before starting is
approximately:
tDELAY,START =
1.5V
1.4A
CSS = 1.1s/F
()C
SS
plus an additional delay, before the output will reach its
regulated value of:
tDELAY,REG
0.8V
1.4A
CSS = 0.6s/F
()C
SS
The start delay can be reduced by using diode D1 in
Figure 14.
APPLICATIONS INFORMATION
Figure 14. RUN/SS Pin Interfacing
3.3V
OR 5V
RUN/SS
D1
CSS
38125 F14
RUN/SS
CSS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3812IFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3831IGN | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3833IUDC#PBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3833EFE#TRPBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO20 |
| LTC3833EUDC#TRPBF | SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3812IFE-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3812IFE-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3813EG#PBF | 功能描述:IC REG CTRLR BST PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC3813EG#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3813IG#PBF | 功能描述:IC REG CTRLR BST PWM CM 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。