- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3722-1 (Linear Technology Corporation) Synchronous Dual Mode Phase Modulated Full Bridge Controllers PDF資料下載
參數資料
| 型號： | LTC3722-1 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
| 中文描述： | 同步相位調制的雙模式全橋控制器 |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 319K |
| 代理商： | LTC3722-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC3722-1/LTC3722-2
14
372212i
LTC3722-1/LTC3722-2 Adaptive Delay Circuitry
The LTC3722-1/LTC3722-2 monitors both the input sup-
ply and instantaneous bridge leg voltages, and commands
a switching transition when the expected zero voltage
condition is reached. DirectSense technology provides
optimal turn-on delay timing, regardless of input voltage,
output load, or component tolerances. The DirectSense
technique requires only a simple voltage divider sense
network to implement. If there is not enough energy to
fully commutate the bridge leg to a ZVS condition, the
LTC3722-1/LTC3722-2 automatically overrides the
DirectSense circuitry and forces a transition. The override
or default delay time is programmed with a resistor from
DPRG to V
REF
.
Adaptive Mode
The LTC3722-1/LTC3722-2 are configured for adaptive
delay sensing with three pins, ADLY, PDLY and SBUS.
ADLY and PDLY sense the active and passive delay legs
respectively via a voltage divider network as shown in
Figure 2.
ADLY and PDLY are connected through voltage dividers to
the active and passive bridge legs respectively. The lower
resistor in the divider is set to 1k. The upper resistor in the
divider is selected for the desired positive transition trip
threshold.
To set up the ADLY and PDLY resistors, first determine at
what drain to source voltage to turn-on the MOSFETs.
Finite delays exist between the time at which the LTC3722-
1/LTC3722-2 controller output transitions, to the time at
which the power MOSFET switches on due to MOSFET
turn on delay and external driver circuit delay. Ideally, we
want the power MOSFET to switch at the instant there is
zero volts across it. By setting a threshold voltage for
ADLY and PDLY corresponding to several volts across the
MOSFET, the LTC3722-1/LTC3722-2 can “anticipate” a
zero voltage VDS and signal the external driver and switch
to turn-on. The amount of anticipation can be tailored for
any application by modifying the upper divider resistor(s).
The LTC3722-1/LTC3722-2 DirectSense circuitry sources
a trimmed current out of PDLY and ADLY after a low to
high level transition occurs. This provides hysteresis and
noise immunity for the PDLY and ADLY circuitry, and sets
the high to low threshold on ADLY or PDLY to nearly the
same level as the low to high threshold, thereby making
the upper and lower MOSFET VDS switch points virtually
identical, independent of V
IN
.
Example: V
IN
= 48V nominal (36V to 72V)
1. Set up SBUS: 1.5V is desired on SBUS with V
IN
= 48V.
Set divider current to 100
μ
A.
R1 = 1.5V/100
μ
A = 15k.
R2 = (48V – 1.5V)/100
μ
A = 465k.
An optional small capacitor (0.001
μ
F) can be added
across R1 to decouple noise from this input.
2. Set up ADLY and PDLY: 7V of “anticipation” is desired
in this circuit to account for the delays of the external
MOSFET driver and gate drive components.
R3, R4 = 1k, sets a nominal 1.5mA in the divider
chain at the threshold.
R5, R6 = (48V – 7V – 1.5V)/1.5mA = 26.3k,
use (2) equal 13k segments.
Figure 2. Adaptive Mode
SBUS
ADLY
PDLY
R2
R5
R6
R1
1k
R3
1k
R4
1k
R
CS
A
B
C
D
V
IN
1922 F02
The threshold voltage on PDLY and ADLY for both the
rising and falling transitions is set by the voltage on SBUS.
A buffered version of this voltage is used as the threshold
level for the internal DirectSense circuitry. At nominal V
IN
,
the voltage on SBUS is set to 1.5V by an external voltage
divider between V
IN
and GND, making this voltage directly
proportional to V
IN
. The LTC3722-1/LTC3722-2
DirectSense circuitry uses this characteristic to zero
voltage switch all of the external power MOSFETs, inde-
pendent of input voltage.
OPERATIOU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3722EGN-1 | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
| LTC3722EGN-2 | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
| LTC1922-1 | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
| LTC1696 | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
| LTC3722-2 | Synchronous Dual Mode Phase Modulated Full Bridge Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3722EGN-1 | 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3722EGN-1#PBF | 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,000 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:50% 電源電壓:9 V ~ 10 V 降壓:無 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 包裝:帶卷 (TR) |
| LTC3722EGN-1#TR | 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3722EGN-1#TRPBF | 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC3722EGN-2 | 功能描述:IC REG CTRLR DIV ISO PWM 24SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。