- 您現在的位置：買賣IC網 > PDF目錄30770 > LTC3615IUF-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC24 PDF資料下載
參數資料
| 型號： | LTC3615IUF-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PQCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, PLASTIC, MO-220WGGD, QFN-24 |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 585K |
| 代理商： | LTC3615IUF-1#PBF |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC3615/LTC3615-1
13
3615fa
Burst Mode Operation—External Clamp
Connecting the MODE pin to a voltage in the range of 0.5V
to 0.8V enables Burst Mode operation with external clamp.
During this mode of operation, the minimum voltage on the
ITH pin is externally set by the voltage on the MODE pin.
It is recommended to use Burst Mode operation with the
internal clamp for ambient temperatures above 85°C.
Pulse-Skipping Mode Operation
Pulse-skipping mode is similar to Burst Mode operation,
but the LTC3615 does not disable power to the internal
circuitry during sleep mode. This improves output voltage
ripple but uses more quiescent current compromising
light load efciency.
Connecting the MODE pin to SVIN enables pulse-skipping
mode. As the load current decreases, the peak inductor
current will be determined by the voltage on the ITH pin
until the ITH voltage drops below 450mV, corresponding
to 0A. At this point switching cycles will be skipped to
keep the output voltage in regulation.
Forced Continuous Mode Operation
In forced continuous mode the inductor current is con-
stantly cycled which creates a minimum output voltage
ripple at all output current levels.
Connecting the MODE pin, to a voltage in the range of
1.1V to SVIN 0.58 will select the forced continuous mode
operation.
The forced continuous mode must be used if the output
is required to sink current.
Dropout Operation
As the input supply voltage approaches the output voltage,
the duty cycle increases toward the maximum on-time.
Further reduction of the supply voltage forces the main
switch to remain on for more than one cycle, eventually
reaching 100% duty cycle. The output voltage will then be
determined by the input voltage minus the voltage drop
across the internal P-channel MOSFET and the inductor.
OPERATION
Figure 2. Modes of Operation
LTC3615
SVIN
VIN
MODE
SGND
0V
2a. Burst Mode Operation
Internally Controlled
LTC3615
SVIN
VIN
MODE
SGND
0V
2c. Pulse-Skipping Mode
LTC3615
SVIN
VIN
MODE
SGND
0V
RM1
RM2
3615 F02
2d. Forced Continuous Mode
2b. Burst Mode Operation
Externally Controlled
LTC3615
SVIN
VIN
MODE
SW1
FB1
SGND
0V
VOUT1
RM1
RM2
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3615EUF#PBF | SWITCHING REGULATOR, PQCC24 |
| LTC3615EFE#PBF | SWITCHING REGULATOR, PDSO24 |
| LTC3615IFE-1#PBF | SWITCHING REGULATOR, PDSO24 |
| LTC3615EUF#TRPBF | SWITCHING REGULATOR, PQCC24 |
| LTC3615IFE#PBF | SWITCHING REGULATOR, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3615IUFPBF | 制造商:Linear Technology 功能描述:Dual 4MHz 3A Synch Step-Down DC/DC QFN24 |
| LTC3615MPFE#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 3A 24TSSOP |
| LTC3615MPFE#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 3A 24TSSOP |
| LTC3615MPFE-1#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 3A 24TSSOP |
| LTC3615MPFE-1#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 3A 24TSSOP |
發布緊急采購，3分鐘左右您將得到回復。