- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC3586EUFE#PBF (LINEAR TECHNOLOGY CORP) 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38 PDF資料下載
參數資料
| 型號： | LTC3586EUFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38 |
| 封裝： | 4 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-38 |
| 文件頁數： | 16/36頁 |
| 文件大?。?/td> | 317K |
| 代理商： | LTC3586EUFE#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3586/LTC3586-1
23
3586fa
always on (and switch B always off), to step-up the input
voltage to the programmed output. If VIN3 is close to the
programmed VOUT3, then the converter will operate in
4-switch mode. In this case the switches sequence through
the pattern of AD, AC, BD to either step the input voltage
up or down to the programmed output.
Buck-Boost Regulator Burst-Mode Operation
In Burst Mode operation, the buck-boost regulator uses
a hysteretic FB3 voltage algorithm to control the output
voltage. By limiting FET switching and using a hysteretic
control loop, switching losses are greatly reduced. In this
mode output current is limited to 50mA typical. While
operating in Burst Mode operation, the output capacitor
is charged to a voltage slightly higher than the regulation
point. The buck-boost converter then goes into a sleep
state, during which the output capacitor provides the load
current. The output capacitor is charged by charging the
inductor until the input current reaches 250mA typical
and then discharging the inductor until the reverse current
reaches 0mA typical. This process is repeated until the
feedback voltage has charged to 6mV above the regulation
point. In the sleep state, most of the regulator’s circuitry
is powered down, helping to conserve battery power.
When the feedback voltage drops 6mV below the regula-
tion point, the switching regulator circuitry is powered on
and another burst cycle begins. The duration for which
the regulator sleeps depends on the load current and
output capacitor value. The sleep time decreases as the
load current increases. The buck-boost regulator will not
go to sleep if the current is greater than 50mA, and if the
load current increases beyond this point while in Burst
Mode operation the output will lose regulation. Burst
Mode operation provides a signicant improvement in
efciency at light loads at the expense of higher output ripple
when compared to PWM mode. For many noise-sensitive
systems, Burst Mode operation might be undesirable at
certain times (i.e. during a transmit or receive cycle of a
wireless device), but highly desirable at others (i.e. when
the device is in low power standby mode). The MODE pin
is used to enable or disable Burst Mode operation at any
time, offering both low noise and low power operation
when they are needed.
Buck-Boost Regulator Soft-Start Operation
Soft-start is accomplished by gradually increasing the
maximum VC3 voltage over a 0.5ms (typical) period.
Ramping the VC3 voltage limits the duty cycle and thus
the VOUT3 voltage minimizing output overshoot during
startup. A soft-start cycle occurs whenever the buck-boost
is enabled, or after a fault condition has occurred (thermal
shutdown or UVLO). A soft-start cycle is not triggered by
changing operating modes. This allows seamless output
operation when transitioning between Burst Mode opera-
tion and PWM mode.
SYNCHRONOUS BOOST DC/DC SWITCHING
REGULATOR
The LTC3586/LTC3586-1 contain a 2.25MHz constant-
frequency current mode synchronous boost switching
regulator with true output disconnect feature. The regulator
provides at least 800mA of output load current and the
output voltage can be programmed up to a maximum of
5V. The converter is enabled by pulling EN4 high. The
boost regulator also includes soft-start to limit inrush
current and voltage overshoot when powering on, short
circuit current protection and switch node slew limiting
circuitry for reduced radiated EMI.
Error Amp
The boost output voltage is programmed by a user-sup-
plied resistive divider returned to the FB4 pin. An internally
compensated error amplier compares the divided output
voltage with an internal 0.8V reference and adjusts the
voltage accordingly until FB4 servos to 0.8V.
Current Limit
Lossless current sensing converts the NMOS switch cur-
rent signal to a voltage to be summed with the internal
slope compensation signal. The summed signal is then
compared to the error amplier output to provide a peak
current control command for the peak comparator. Peak
switch current is limited to 2.4A independent of output
voltage.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3586EUFE-1#PBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3586EUFE-1#TRPBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3672BEDC-1#PBF | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3728LZEUH | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3773EUHF | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3586EUFE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Effi ciency USB Power Manager with Boost, Buck-Boost and Dual Bucks |
| LTC3588-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Voltage Step-Up Converter |
| LTC3588-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:400mA Step-Up DC/DC Converter with Maximum Power Point Control and 250mV Start-Up |
| LTC3588-2_10 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Piezoelectric Energy Harvesting Power Supply with 14V Minimum VIN |
| LTC3588EDD-1#PBF | 功能描述:IC ENERGY HARVESTING PSU 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。