- 您現在的位置：買賣IC網 > PDF目錄30770 > LTC3546EFE#PBF (LINEAR TECHNOLOGY CORP) DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | LTC3546EFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-28 |
| 文件頁數： | 15/28頁 |
| 文件大?。?/td> | 356K |
| 代理商： | LTC3546EFE#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC3546
22
3546fb
APPLICATIONS INFORMATION
tion to exceed the maximum junction temperature of the
part. In a majority of applications, the LTC3546 does not
dissipate much heat due to its high efciency. However, in
applications where the LTC3546 is running at high ambient
temperature with low supply voltage and high duty cycles,
such as in dropout, the heat dissipated may exceed the
maximum junction temperature of the part. If the junction
temperature reaches approximately 150°C, both switches
in both regulators will be turned off and the SW nodes will
become high impedance.
To avoid the LTC3546 from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum
junction temperature of the part. The temperature rise is
given by:
TRISE = PD θJA
where PD is the power dissipated by the regulator and θJA
is the thermal resistance from the junction of the die to
the ambient temperature.
The junction temperature, TJ, is given by:
TJ = TRISE + TAMBIENT
As an example, consider the case when the LTC3546 is
in dropout in both regulators at an input voltage of 3.3V
with load currents of 3A (SW1D externally connected to
SW2) and 1A. From the Typical Performance Character-
istics graph of Switch Resistance, the RDS(ON) resistance
of the 3A P-channel switch parallel combination of SW2
and SW1D is 0.06Ω and the RDS(ON) of the 1A P-channel
switch is 0.18Ω. The power dissipated by the part is:
PD = I12 RDS(ON)1 + I22 RDS(ON)2
PD = 32 0.064 + 12 0.19
PD = 0.77W
The UFD package junction-to-ambient thermal resistance,
θJA, is about 34°C/W. Therefore, the junction temperature
of the regulator operating in a 85°C ambient temperature
is approximately:
TJ = 0.77 34 + 85
TJ = 111.2°C
This junction temperature is obtained from an RDS(ON) at
25°C. At 125°C the RDS(ON) increases by about 30%. This
will put the junction temperature at 122°C. If the supply is
lower, like 2.25V, the RDS(ON) is higher still. Special care
needs to be taken if the part is expected to be operating
in dropout so that the maximum junction temperature of
125°C is not exceeded.
Design Example
As a design example, consider using the LTC3546 in a
portable application with a Li-Ion battery. The battery
provides a VIN = 2.25V to 4.2V. One output requires 1.8V
at 2.5A in active mode, and 1mA in standby mode. The
other output requires 1.2V at 800mA in active mode,
and 500μA in stand-by mode. Since both loads still need
power in stand-by, Burst Mode operation is selected for
good low load efciency.
First, determine what frequency should be used. Higher
frequency results in a lower inductor value for a given ΔIL
(ΔIL is estimated as 0.35ILOAD(MAX)). Reasonable values
for wire wound surface mount inductors are in the 1μH
and up. Look at the different frequencies with the ΔIL =
0.35ILOAD(MAX).
CONVERTER OUTPUT
ILOAD(MAX)
ΔIL
SW2/SW1D, 1.2V
2.5A
875mA
SW1, 1.8V
800mA
280mA
Using the 1.5MHz frequency setting (FREQ = 143k to GNDA)
we get the following equations for L1 and L2.
L1=
1.2V
1.5MHz 280mA
1
1.2V
4.2V
= 2H
L2 =
1.8V
1.5MHz 875mA
1
1.8V
4.2V
= 0.78H
Use 1μH and 2.2μH.
COUT selection is typically based on load step rather
than the ripple requirements. The minimum required
capacitance will increase with a decrease in compensa-
tion loop bandwidth and/or increases in maximum load
step or output voltage tolerance. A good starting point is
about 22μF per ampere of output current for a nominal
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3546EUFD#PBF | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546IUFD | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546EUFD | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546IUFD#TR | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546EFE | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3546EFETRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546EUFD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A/2A 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LTC3546EUFD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A/2A 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LTC3546EUFDPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546EUFDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
發布緊急采購，3分鐘左右您將得到回復。