- 您現在的位置：買賣IC網 > PDF目錄30770 > LTC3536IMSE#PBF (LINEAR TECHNOLOGY CORP) 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO12 PDF資料下載
參數資料
| 型號： | LTC3536IMSE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO12 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-12 |
| 文件頁數： | 26/28頁 |
| 文件大?。?/td> | 1088K |
| 代理商： | LTC3536IMSE#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
LTC3536
7
3536f
PIN FUNCTIONS (DFN/MSOP)
RT (Pin 1/Pin 1): Oscillator Frequency Programming
Input. Connect a resistor from RT to GND to program the
internal oscillator frequency. The frequency is given by:
fOSC (MHz) = 100/RT (kΩ)
where RT is in kΩ and fOSC is between 0.3MHz and 2MHz.
Tying the RT pin to VIN enables the internal 1.2MHz default
oscillator frequency.
SGND (Pin 2/Pin 2): Ground Connection for the LTC3536.
A ground plane is highly recommended. Sensitive analog
components terminated at ground should connect to the
GND pin with a Kelvin connection, separated from the
high current path.
MODE/SYNC (Pin 3/Pin 3): Pulse Width Modulation/Burst
Mode Selection and Synchronization Input. Driving MODE
to a logic 0 state programs fixed frequency, low noise
PWM operation. Driving MODE to logic 1 state programs
Burst Mode operation for highest efficiency at light loads.
In Burst Mode operation, the output current capability is
significantly less than what is available in PWM operation.
Refer to the Applications Information section of this data
sheet for details. Frequency synchronization is achieved
if a clock pulse is applied to MODE/SYNC. The external
clock pulse amplitude must have an amplitude equal or
higher than 1.2V and duty cycle from 10% and 90%. The
free-running frequency of the LTC3536 oscillator can be
programmed slower or faster than the synchronization
clock frequency.
SW1 (Pin 4/Pin 4): Switch Pin. Connect to internal power
switches A and B. Connect one side of the buck-boost
inductor to SW1. Provide a short wide PCB trace from the
inductor to SW1 to minimize voltage transients and noise.
SW2 (Pin 5/Pin 6): Switch Pin. Connect to internal power
switches C and D. Connect one side of the buck-boost
inductor to SW2. Provide a short wide PCB trace from the
inductor to SW2 to minimize voltage transients and noise.
VOUT (Pin 6/Pin 7): Output Voltage. This pin is the power
output for the regulator. A low ESR capacitor should be
placed between this pin and the ground plane. The capaci-
tor should be placed as close to this pin as possible and
have a short return path to ground.
VIN (Pin 7/Pins 8, 9): Power Input for the Converter. A low
ESR 10F or larger bypass capacitor should be connected
between this pin and ground. The capacitor should be
placed as close to this pin as possible and have a short
return path to ground.
SHDN (Pin 8/Pin 10): Enable Input. A logic 1 on SHDN
activates the buck-boost regulator. A logic 0 on SHDN
deactivates the buck-boost regulator.
FB (Pin 9/Pin 11): Output Voltage Programming Feedback
DividerInput.Theregulatoroutputvoltageisprogrammed
by the voltage divider connected to FB. The buck-boost
output is given by the following equation:
VOUT = 0.6V (1 + RTOP/RBOT) (V)
whereRBOTisaresistorconnectedbetweenFBandground
and RTOP is a resistor connected between FB and VOUT.
The buck-boost output voltage can be adjusted from 1.8V
to 5.5V.
VC (Pin 10/Pin 12): Error Amplifier Output. Frequency
compensation components are connected between VC
and FB to provide stable operation of the converter. Refer
to the Applications Information section of this data sheet
for design details.
PGND (Exposed Pad Pin 11/ Pin 5): Power Ground. The
exposed pad must be soldered to the PCB and electrically
connected to ground through the shortest and lowest im-
pedance connection possible. The MSOP exposed pad is
electrical ground and must be soldered to the PCB ground
for rated thermal performance and load regulation.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3536EDD#PBF | 4 A SWITCHING REGULATOR, 1440 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC3546EFE#PBF | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3546EUFD#PBF | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546IUFD | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3546EUFD | DUAL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3537 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
| LTC3537EUD#PBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LTC3537EUD#TRPBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LTC3537EUD-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
| LTC3537EUD-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
發布緊急采購，3分鐘左右您將得到回復。