- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC3522EUD#TR (LINEAR TECHNOLOGY CORP) 0.85 A DUAL SWITCHING CONTROLLER, 1330 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LTC3522EUD#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.85 A DUAL SWITCHING CONTROLLER, 1330 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, PLASTIC, M0-220WEED-2, QFN-16 |
| 文件頁數： | 3/20頁 |
| 文件大?。?/td> | 270K |
| 代理商： | LTC3522EUD#TR |
LTC3522
11
3522f
response of the compensation network. The ratio of R2 to
R1 must be set to program the desired output voltage but
this still allows the value of R2 to be adjusted to optimize
the transient response of the converter. Increasing the value
of R2 generally leads to greater stability at the expense of
reduced transient response speed. Increasing the value of
R2 can yield substantial transient response improvement in
cases where the phase margin has been reduced due to the
use of a small value output capacitor or a large inductance
(particularly with large boost step-up ratios). Conversely,
decreasing the value of R2 increases the loop bandwidth
which can improve the speed of the converter’s transient
response. This can be useful in improving the transient
response if a large valued output capacitor is utilized. In
this case, the increased bandwidth created by decreasing
R2 is used to counteract the reduced converter bandwidth
caused by the large output capacitor.
Current Limit Operation
The buck-boost converter has two current limit circuits.
The primary current limit is an average current limit circuit
which injects an amount of current into the feedback node
which is proportional to the extent that the switch A cur-
rent exceeds the current limit value. Due to the high gain
of this loop, the injected current forces the error amplier
output to decrease until the average current through switch
A decreases approximately to the current limit value. The
average current limit utilizes the error amplier in an ac-
tive state and thereby provides a smooth recovery with
little overshoot once the current limit fault condition is
removed. Since the current limit is based on the average
current through switch A, the peak inductor current in
current limit will have a dependency on the duty cycle
(i.e., on the input and output voltages in the overcurrent
condition).
The speed of the average current limit circuit is limited by
the dynamics of the error amplier. On a hard output short,
it would be possible for the inductor current to increase
substantially beyond current limit before the average cur-
rent limit circuit would react. For this reason, there is a
second current limit circuit which turns off switch A if the
current ever exceeds approximately 165% of the average
current limit value. This provides additional protection in
the case of an instantaneous hard output short.
Reverse Current Limit
The reverse current comparator on switch D monitors
the inductor current entering VOUT1. When this current
exceeds 250mA (typical) switch D will be turned off for
the remainder of the switching cycle.
Burst Mode Operation
With the PWM pin held low, the buck-boost converter
operates utilizing a variable frequency switching algorithm
designed to improve efciency at light load and reduce
the standby current at zero load. In Burst Mode operation,
the inductor is charged with xed peak amplitude current
pulses. These current pulses are repeated as often as
necessary to maintain the output regulation voltage. The
typical output current which can be supplied in Burst Mode
operaton is dependent upon the input and output voltage
as given by the following formula:
I
V
VV
A
OUT MAX BURST
IN
OUT
(),
.
=
+
()
011
In Burst Mode operation, the error amplier is not used but
is instead placed in a low current standby mode to reduce
supply current and improve light load efciency.
Soft-Start
The buck-boost converter has an internal voltage mode
soft-start circuit with a nominal duration of 600μs. The
converter remains in regulation during soft-start and will
therefore respond to output load transients that occur
during this time. In addition, the output voltage rise time
OPERATION
1V
GND
VOUT1
LTC3522
VOUT
FB1
R2
R1
3522 F02
+
–
Figure 2. Buck-Boost Error Amplier and Compensation
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3525LESC6-3#PBF | 0.45 A SWITCHING REGULATOR, PDSO6 |
| LTC3526LEDC | SWITCHING CONTROLLER, 1250 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3531ES6-3.3#PBF | 0.46 A SWITCHING REGULATOR, PDSO6 |
| LTC3538EDCB#TRM | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3542IS6#PBF | SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3523 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3523EUD#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3523EUD#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3523EUD-2#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3523EUD-2#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。