- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3458 (Linear Technology Corporation) ECONOLINE: RSZ/P - 1kVDC PDF資料下載
參數資料
| 型號： | LTC3458 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 8位微控制器 |
| 英文描述： | ECONOLINE: RSZ/P - 1kVDC |
| 中文描述： | ECONOLINE：RSZ / P - 1kVDC 2kVDC隔離UL94V - 0封裝材料所需的散熱片，無外置。組件所需的環形磁ContinuousShort電路保護（/ P的后綴） |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 389K |
| 代理商： | LTC3458 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LTC3458L
10
3458lf
transition occurs using a single resistor. During Burst
Mode operation, the oscillator is shut down, since the on
time is determined by the time it takes the inductor current
to reach a fixed peak current, and the off time is deter-
mined by the time it takes for the inductor current to return
to zero.
In Burst Mode operation, the IC delivers energy to the
output until it is regulated and then goes into a sleep mode
where the outputs are off and the IC is consuming only
12
μ
A of quiescent current. In this mode the output ripple
voltage has a variable frequency component with load
current and will be typically 2% peak-to-peak. This maxi-
mizes efficiency at very light loads by minimizing switch-
ing and quiescent losses. Burst Mode ripple can be re-
duced slightly by using more output capacitance (22
μ
F or
greater). This capacitor does not need to be a low ESR type
if low ESR ceramics are also used. Another method of
reducing Burst Mode ripple is to place a small feed-
forward capacitor across the upper resistor in the V
OUT
feedback divider network.
During Burst Mode operation, COMP is disconnected
from the error amplifier in an effort to hold the voltage on
the external compensation network where it was before
entering Burst Mode operation. To minimize the effects of
leakage current and stray resistance, voltage clamps limit
the minimum and maximum voltage on COMP during
Burst Mode operation. This minimizes the transient expe-
rienced when a heavy load is suddenly applied to the
converter after being in Burst Mode operation for an
extended period of time.
For automatic operation, an RC network should be con-
nected from BURST to ground. The value of the resistor
will control the average load current (I
BURST
) at which
Burst Mode operation will be entered and exited (there is
hysteresis to prevent oscillation between modes). The
equation given for the capacitor on BURST is for the
minimum value, to prevent ripple on the BURST pin from
causing the part to oscillate in and out of Burst Mode
operation at the current where the mode transition occurs.
10
R
I
BURST
BURST
=
where R
BURST
is in k
and I
BURST
is in amps.
C
C
V
BURST
OUT
10 000
OUT
=
,
where C
BURST(MIN)
and C
OUT
are in
μ
F.
Note: the BURST pin only sources current based on
current delivered to V
OUT
through the P-channel MOSFET.
If current in the inductor is allowed to go negative (this can
occur at very light loads and high step-up ratios), the burst
threshold may become inaccurate, preventing the IC from
entering Burst Mode operation. For R
BURST
values greater
than 200k, a larger than recommended inductor value may
be needed to ensure positive inductor current and auto-
matic Burst Mode operation.
In the event that a sudden load transient causes the voltage
level on FB to drop by more than 4% from the regulation
value, an internal pull-up is applied to BURST, forcing the
part quickly out of Burst Mode operation. For optimum
transient response when going between Burst Mode op-
eration and PWM mode, Burst can be controlled manually
by the host. This way PWM mode can be commanded
before the load step occurs, minimizing output voltage
drop. Note that Burst Mode operation is inhibited during
start-up and soft-start.
Manual Control
For applications requiring fixed frequency operation at all
load currents, connect the BURST pin to V
OUT
through a
51k resistor. To force Burst Mode operation, ground the
BURST pin.
For applications where a large load step can be anticipated,
the circuit below can be used to reduce the voltage transient
on V
OUT
. Automatic operation is achieved when the exter-
nal P-channel MOSFET is off and fixed frequency operation
is commanded when the external P-channel MOSFET is on.
In shutdown, the P-channel MOSFET should be off.
APPLICATIOU
W
U
U
Figure 1
0.01
μ
F
V
IN
BURST
133k
P-CHANNEL
MOSFET
HIGH: AUTO MODE
LOW: FIXED FREQUENCY
3458L FO1
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3458LEDE | 1.7A, 1.5MHz Synchronous Step-Up DC/DC Converter with Output Disconnect |
| LTC3548EDD | Dual Synchronous,400mA/800mA, 2.25MHz Step-Down DC/DC Regulator |
| LTC3252 | ECONOLINE: RSZ/P - 1kVDC |
| LT3407 | Dual Synchronous,400mA/800mA, 2.25MHz Step-Down DC/DC Regulator |
| LT3407-2 | Dual Synchronous,400mA/800mA, 2.25MHz Step-Down DC/DC Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3458EDE | 功能描述:IC REG BOOST SYNC ADJ 1.4A 12DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3458EDE#PBF | 功能描述:IC REG BOOST SYNC ADJ 1.4A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3458EDE#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 1.4A 12DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3458L | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.7A, 1.5MHz Synchronous Step-Up DC/DC Converter with Output Disconnect |
| LTC3458LEDE | 功能描述:IC REG BOOST SYNC ADJ 1.4A 12DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。