- 您現在的位置：買賣IC網 > PDF目錄377775 > LTC3423 (Linear Integrated Systems) Low Output Voltage 3MHz Micropower Synchronous Boost Converters PDF資料下載
參數資料
| 型號： | LTC3423 |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| 中文描述： | 低輸出電壓3MHz的微功率同步升壓轉換器 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 203K |
| 代理商： | LTC3423 |
9
LTC3423/LTC3424
34234f
Operating Frequency Selection
There are several considerations in selecting the operat-
ing frequency of the converter. The first is determining the
sensitive frequency bands that cannot tolerate any spec-
tral noise. For example, in products incorporating RF
communications, the 455kHz IF frequency is sensitive to
any noise, therefore switching above 600kHz is desired.
Some communications have sensitivity to 1.1MHz. In this
case, converter frequencies up to 3MHz may be em-
ployed.
The second consideration is the physical size of the
converter. As the operating frequency goes up, the induc-
tor and filter caps go down in value and size. The trade off
is in efficiency since the switching losses due to gate
charge are going up proportional with frequency.
Another operating frequency consideration is whether the
application can allow “pulse skipping.” In this mode, the
minimum on time of the converter cannot support the duty
cycle, so the converter ripple will go up and there will be
a low frequency component of the output ripple. In many
applications where physical size is the main criterion then
running the converter in this mode is acceptable. In
applications where it is preferred not to enter this mode,
then the maximum operating frequency is given by:
f
V
V
V
t
Hz
MAX NOSKIP
_
OUT
IN
OUT
ON MIN
(
)
–
=
where t
ON(MIN)
= minimum on time = 140ns
Reducing Output Capacitance with a Load Feed
Forward Signal
In many applications the output filter capacitance can be
reduced for the desired transient response by having the
device commanding the change in load current, (i.e.
system microcontroller), inform the power converter of
the changes as they occur. Specifically, a “l(fā)oad feed
forward” signal coupled into the V
C
pin gives the inner
current loop a head start in providing the change in output
current. The transconductance of the LTC3423 converter
at the V
C
pin with respect to the inductor current is typically
APPLICATIU
W
U
U
130mA/100mV, and the LTC3424 is typically 170mA/
100mV, so the amount of signal injected is proportional to
the anticipated change of inductor current with load. The
outer voltage loop performs the remainder of the correc-
tion, but because of the load feed forward signal, the range
over which it must slew is greatly reduced. This results in
an improved transient response. A logic level feed forward
signal, V
FF
, is coupled through components C5 and R6.
The amount of feed forward signal is attenuated with
resistor R6 and is given by the following relationship:
R
V
R
V
V
I
R
FF
IN
OUT
OUT
6
5
1 5
5
≈
–
where
I
OUT
= load current change.
Figure 2
6
10
3
2
1
3423/24 F02
LTC3423/LTC3424
V
DD
SHDN
V
IN
MODE/SYNC
R
t
SW
V
OUT
FB
V
C
GND
4
7
8
9
5
R5
C3
LOAD FEED
FORWARD
SIGNAL
V
FF
R6
C5
3.3nF
V
IN
V
DD
IN
V
OUT
Closing the Feedback Loop
The LTC3423/LTC3424 uses current mode control with
internal adaptive slope compensation. Current mode con-
trol eliminates the 2nd order filter due to the inductor and
output capacitor exhibited in voltage mode controllers,
and simplifies it to a single-pole filter response. The
product of the modulator control to output DC gain plus
the error amp open-loop gain equals the DC gain of the
system.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3423EMS | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3424 | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3424EMS | Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
| LTC3442 | Micropower Synchronous Buck-Boost DC/DC Converter with Automatic Burst Mode Operation |
| LTC3442EDE | Micropower Synchronous Buck-Boost DC/DC Converter with Automatic Burst Mode Operation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3423EMS | 功能描述:IC REG BOOST SYNC ADJ 1A 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LTC3423EMS#PBF | 功能描述:IC REG BOOST SYNC ADJ 1A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LTC3423EMS#TR | 功能描述:IC REG BOOST SYNC ADJ 1A 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3423EMS#TRPBF | 功能描述:IC REG BOOST SYNC ADJ 1A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC3424 | 制造商:LINEAR 制造商全稱:LINEAR 功能描述:Low Output Voltage 3MHz Micropower Synchronous Boost Converters |
發布緊急采購，3分鐘左右您將得到回復。