- 您現在的位置：買賣IC網 > PDF目錄377772 > LTC2902-1CGN (Linear Integrated Systems) Programmable Quad Supply Monitor with Adjustable Reset Timer and Supply Tolerance PDF資料下載
參數資料
| 型號： | LTC2902-1CGN |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Programmable Quad Supply Monitor with Adjustable Reset Timer and Supply Tolerance |
| 中文描述： | 可編程四路電源監視器可調復位定時器和供應公差 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 206K |
| 代理商： | LTC2902-1CGN |
12
LTC2902
2902f
APPLICATIOU
particular output is known, output fall time (10% to 90%)
is estimated using:
t
FALL
≈
2.2 R
PD
C
LOAD
where R
PD
is the on-resistance of the internal pull-down
transistor. The typical performance curve (V
OL
vs I
SINK
)
demonstrates that the pull-down current is somewhat
linear versus output voltage. Using the 25
°
C curve, R
PD
is
estimated to be approximately 40
. Assuming a 150pF
load capacitance, the fall time is about 13.2ns.
Although the outputs are considered to be “open-drain,”
they do have a weak pull-up capability (see COMPX or RST
Pull-Up Current vs V2 curve). Output rise time (10% to
90%) is estimated using:
t
RISE
≈
2.2 R
PU
C
LOAD
where R
PU
is the on-resistance of the pull-up transistor.
The on-resistance as a function of the V2 voltage at room
temperature is estimated using:
5
–
with V2 = 3.3V, R
PU
is about 260k. Using 150pF for load
capacitance, the rise time is 86
μ
s. If the output needs to
pull up faster and/or to a higher voltage, a smaller
external pull-up resistor may be used. Using a 10k pull-
up resistor, the rise time is reduced to 3.3
μ
s for a 150pF
load capacitance.
The LTC2902-2 has an active pull-up to V2 on the RST
output. The typical performance curve (RST Pull-Up Cur-
rent vs V2 curve) demonstrates that the pull-up current is
somewhat linear versus the V2 voltage and R
PU
is esti-
mated to be approximately 625
. A 150pF load capaci-
tance makes the rise time about 206ns.
W
U
U
R
V
PU
=
6 10
2 1
Selecting the Reset Timing Capacitor
The reset time-out period is adjustable in order to accom-
modate a variety of microprocessor applications. The
reset time-out period, t
RST
, is adjusted by connecting a
capacitor, C
RT
, between the CRT pin and ground. The value
of this capacitor is determined by:
C
RT
= t
RST
217 10
–9
with C
RT
in Farads and t
RST
in seconds. The C
RT
value per
millisecond of delay can also be expressed as C
RT
/ms =
217 (pF/ms).
Leaving the CRT pin unconnected will generate a mini-
mum reset time-out of approximately 50
μ
s. Maximum
reset time-out is limited by the largest available low
leakage capacitor. The accuracy of the time-out period will
be affected by capacitor leakage (the nominal charging
current is 2
μ
A) and capacitor tolerance. A low leakage
ceramic capacitor is recommended.
Tolerance Programming and the RESET Disable
Using the two digital inputs T0 and T1, the user can
program the global supply tolerance for the LTC2902 (5%,
7.5%, 10%, 12.5%). The larger tolerances provide more
headroom by lowering the trip thresholds.
Table 4. Tolerance Programming
T0
Low
Low
High
High
T1
Low
High
Low
High
TOLERANCE (%)
5
7.5
10
12.5
V
REF
(V)
1.210
1.178
1.146
1.113
Under conventional operation, RST and COMPX will go
low when V
X
is below its threshold. At any time, the RDIS
pin can be pulled low, overriding the reset operation and
forcing the RST pin high. This feature is useful when
determining supply margins under processor control since
the reset command will not be invoked. The RDIS pin is
connected to a weak internal pull-up to V
CC
(10
μ
A typ),
allowing the pin to be left floating if unused.
Ensuring RST Valid for V
CC
Down to 0V (LTC2902-2)
When V
CC
is below 1V the RST pull-down capability is
drastically reduced. The RST pin may float to undeter-
mined voltages when connected to high impedance (such
as CMOS logic inputs). The addition of a pull-down resis-
tor from RST to ground will provide a path for stray charge
and/or leakage currents. The resistor value should be
small enough to provide effective pull-down without ex-
cessively loading the pull-up circuitry. Too large a value
may not pull down well enough. A 100k resistor from RST
to ground is satisfactory for most applications.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2902-1IGN | Programmable Quad Supply Monitor with Adjustable Reset Timer and Supply Tolerance |
| LTC2902-2CGN | Programmable Quad Supply Monitor with Adjustable Reset Timer and Supply Tolerance |
| LTC2902-2IGN | Programmable Quad Supply Monitor with Adjustable Reset Timer and Supply Tolerance |
| LTC2902 | Precision Quad Supply Monitor in 6-Lead SOT-23 |
| LTC2903IS6-A1 | Precision Quad Supply Monitor in 6-Lead SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2902-1CGN#PBF | 功能描述:IC MONITOR SUPPLY QUAD 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V，2.955V，可調，可調，可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6 |
| LTC2902-1CGN#PBF | 制造商:Linear Technology 功能描述:SUPPLY MONITOR, QUAD, ADJ, 43UA, SSOP-16 |
| LTC2902-1CGN#TR | 功能描述:IC MONITOR SUPPLY QUAD 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC2902-1CGN#TRPBF | 功能描述:IC MON SUPP QD W/RST&SEL 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| LTC2902-1IGN | 功能描述:IC MONITOR SUPPLY QUAD 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
發布緊急采購，3分鐘左右您將得到回復。