- 您現在的位置：買賣IC網 > PDF目錄10145 > LTC2850HS8#TRPBF (Linear Technology)IC TXRX RS485 20MBPS 8-SOIC PDF資料下載
參數資料
| 型號： | LTC2850HS8#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 3/18頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485 20MBPS 8-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
LTC2850/LTC2851/LTC2852
285012fd
applicaTions inForMaTion
Driver
ThedriverprovidesfullRS485/RS422compatibility.When
enabled, if DI is high, Y-Z is positive for the full-duplex
devices (LTC2851, LTC2852) and A-B is positive for the
half-duplex device (LTC2850).
When the driver is disabled, both outputs are high im-
pedance. For the full-duplex devices, the leakage on the
driver output pins is guaranteed to be less than 10A
over the entire common mode range of –7V to 12V. On
the half-duplex LTC2850, the impedance is dominated by
the receiver input resistance, RIN.
Driver Overvoltage and Overcurrent Protection
The driver outputs are protected from short-circuits
to any voltage within the Absolute Maximum range of
(VCC – 15V) to 15V. The typical peak current in this condi-
tion does not exceed 180mA.
If a high driver output is shorted to a voltage just above
VCC, a reverse current will flow into the supply. When
this voltage exceeds VCC by about 1.4V, the reverse
current turns off. Preventing the driver from turning off
with outputs shorted to output voltages just above VCC
keeps the driver active even for receiver loads that have
a positive common mode with respect to the driver—
a valid condition.
The worst-case peak reverse short-circuit current can
be as high as 300mA in extreme cold conditions. If this
current can not be absorbed by the supply, a 3.6V Zener
diode can be added in parallel with the supply to sink this
current.
All devices also feature thermal shutdown protection that
disables the driver and receiver in case of excessive power
dissipation (see Note 4 in the Electrical Characteristics
section).
Receiver and Failsafe
With the receiver enabled, when the absolute value of
the differential voltage between the A and B pins is
greater than 200mV, the state of RO will reflect the polar-
ity of (A-B)
These parts have a failsafe feature that guarantees the
receiver output to be in a logic-high state when the
inputs are either shorted, left open, or terminated but
not driven. This failsafe feature is guaranteed to work
for inputs spanning the entire common mode range of
–7V to 12V.
The receiver output is internally driven high (to VCC) or
low (to ground) with no external pull-up needed. When
the receiver is disabled the RO pin becomes Hi-Z with
leakage of less than ±1A for voltages within the supply
range.
Receiver Input Resistance
The receiver input resistance from A or B to ground is
guaranteed to be greater than 96k (C, I-grade). This is 8x
higher than the requirements for the RS485 standard and
thus this receiver represents a one-eighth unit load. This,
in turn, means that 8x the standard number of receivers,
or 256 total, can be connected to a line without loading
it beyond what is specified in the RS485 standard. The
receiver input resistance from A or B to ground on high
temperature H-grade parts is greater than 48k providing
a one-quarter unit load. The high input resistance of the
receiver is maintained whether it is enabled or disabled,
powered or unpowered.
Supply Current
The unloaded static supply currents in these devices are
very low, typically under 500A for all modes of opera-
tion. In applications with resistively terminated cables,
the supply current is dominated by the driver load. For
example, when using two 120
Ω terminators with a dif-
ferential driver output voltage of 2V, the DC load current
is 33mA, which is sourced by the positive voltage supply.
Power supply current increases with toggling data due to
capacitive loading and this term can increase significantly
at high data rates. Figure 13 shows supply current vs
data rate for two different capacitive loads for the circuit
configuration of Figure 4.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2850HMS8#TRPBF | IC TXRX RS485 20MBPS 8-MSOP |
| MS3102A20-20P | CONN RCPT 4POS BOX MNT W/PINS |
| D38999/20FE26PB | CONN RCPT 26POS WALL MNT W/PINS |
| MS3101R12S-3P | CONN RCPT 2POS PANEL MNT W/PINS |
| MS27656T17B55P | CONN RCPT 55POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2850IDD#PBF | 功能描述:IC TXRX RS485 20MBPS 8-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| LTC2850IDD#TRPBF | 功能描述:IC TXRX RS485 20MBPS 8-DFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| LTC2850IMS8#PBF | 功能描述:IC TXRX RS485/RS422 8MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| LTC2850IMS8#TRPBF | 功能描述:IC TXRX RS485 20MBPS 8-MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| LTC2850IS8#PBF | 功能描述:IC TXRX RS485/RS422 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
發布緊急采購，3分鐘左右您將得到回復。