- 您現在的位置：買賣IC網 > PDF目錄10328 > LTC2435-1CGN (Linear Technology)IC ADC DIFF I/REF 20BIT 16-SSOP PDF資料下載
參數資料
| 型號： | LTC2435-1CGN |
| 廠商： | Linear Technology |
| 文件頁數： | 5/42頁 |
| 文件大小： | 0K |
| 描述： | IC ADC DIFF I/REF 20BIT 16-SSOP |
| 標準包裝： | 100 |
| 位數： | 20 |
| 采樣率（每秒）： | 13.75 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 1mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，雙極 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC2435/LTC2435-1
13
24351fc
For more information www.linear.com/LTC2435
applicaTions inForMaTion
The LTC2435/LTC2435-1 perform a full-scale calibration
every conversion cycle. This calibration is transparent to
theuserandhasnoeffectonthecyclicoperationdescribed
above. The advantage of continuous calibration is extreme
stability of full-scale readings with respect to time, supply
voltage change and temperature drift.
Unlike the LTC2430, the LTC2435 and LTC2435-1 do not
perform an offset calibration every conversion cycle. This
enablestheLTC2435/LTC2435-1todoubletheiroutputrate
whilemaintaininglinefrequencyrejection.Theinitialoffset
of the LTC2435/LTC2435-1 is within 5mV independent of
VREF . Based on the LTC2435/LTC2435-1 new modulator
architecture, the temperature drift of the offset is less than
100nV/°C. More information on the LTC2435/LTC2435-1
offset is described in the Offset Accuracy and Drift section
of this data sheet.
Power-Up Sequence
The LTC2435/LTC2435-1 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 2.2V. This feature guarantees the
integrity of the conversion result and of the serial interface
mode selection. (See the 2-wire I/O sections in the Serial
Interface Timing Modes section.)
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signalwithadurationofapproximately1ms.ThePORsignal
clears all internal registers. Following the POR signal, the
LTC2435/LTC2435-1 start a normal conversion cycle and
follow the succession of states described above. The first
conversion result following POR is accurate within the
specifications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
Reference Voltage Range
These converters accept a truly differential external
reference voltage. The absolute/common mode voltage
specification for the REF+ and REF– pins covers the entire
rangefromGNDtoVCC.Forcorrectconverteroperation,the
REF+ pin must always be more positive than the REF– pin.
TheLTC2435/LTC2435-1canacceptadifferentialreference
voltage from 0.1V to VCC. The converter output noise is
determined by the thermal noise of the front-end circuits,
and as such, its value is nearly constant with reference
voltage. A decrease in reference voltage will not signifi-
cantly improve the converter’s effective resolution. On the
other hand, a reduced reference voltage will improve the
converter’s overall INL performance. A reduced reference
voltage will also improve the converter performance when
operated with an external conversion clock (external FO
signal) at substantially higher output data rates (see the
Output Data Rate section).
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2435/LTC2435-1 convert the bipolar dif-
ferential input signal, VIN = IN+ – IN–, from –FS = –0.5
VREF to + FS = 0.5 VREF where VREF = REF+ – REF–.
Outside this range, the converters indicate the overrange
or the underrange condition using distinct output codes.
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the perfor-
mance of the device. In the physical layout, it is important
to maintain the parasitic capacitance of the connection
between these series resistors and the corresponding
pins as low as possible; therefore, the resistors should
be located as close as practical to the pins. The effect of
the series resistance on the converter accuracy can be
evaluated from the curves presented in the Input Current/
Reference Current sections. In addition, series resistors
will introduce a temperature dependent offset error due
to the input leakage current. A 1nA input leakage current
will develop a 1ppm offset error on a 5k resistor if VREF =
5V. This error has a very strong temperature dependency.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7911AUJZ-R2 | IC ADC 10BIT 250KSPS TSOT23-8 |
| MS27467T11F35SA | CONN PLUG 13POS STRAIGHT W/SCKT |
| LTC2430CGN#PBF | IC ADC 20BIT DIFFINPUT/REF16SSOP |
| LTC2430CGN | IC ADC 20BIT DIFFINPUT/REF16SSOP |
| AD7914BRUZ-REEL7 | IC ADC 10BIT 4CH W/SEQ 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2435-1CGN#PBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2435-1CGN#TR | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1CGN#TRPBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN#PBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。