- 您現在的位置：買賣IC網 > PDF目錄377727 > LTC2433-1CMS (Linear Integrated Systems) Differential Input 16-Bit No Latency DS ADC PDF資料下載
參數資料
| 型號： | LTC2433-1CMS |
| 廠商： | Linear Integrated Systems |
| 英文描述： | Differential Input 16-Bit No Latency DS ADC |
| 中文描述： | 差分輸入16位ADC的無延遲局副局長 |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 298K |
| 代理商： | LTC2433-1CMS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2433-1
9
24331fa
The LTC2433-1 performs offset and full-scale calibrations
every conversion cycle. This calibration is transparent to
the user and has no effect on the cyclic operation de-
scribed above. The advantage of continuous calibration is
extreme stability of offset and full-scale readings with re-
spect to time, supply voltage change and temperature drift.
Power-Up Sequence
The LTC2433-1 automatically enters an internal reset state
when the power supply voltage V
CC
drops below approxi-
mately 2V. This feature guarantees the integrity of the
conversion result and of the serial interface mode selec-
tion. (See the 2-wire I/O sections in the Serial Interface
Timing Modes section.)
When the V
CC
voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with a typical duration of 1ms. The POR signal clears
all internal registers. Following the POR signal, the
LTC2433-1 starts a normal conversion cycle and follows
the succession of states described above. The first con-
version result following POR is accurate within the speci-
fications of the device if the power supply voltage is restored
within the operating range (2.7V to 5.5V) before the end of
the POR time interval.
Reference Voltage Range
This converter accepts a truly differential external refer-
ence voltage. The absolute/common mode voltage speci-
fication for the REF
+
and REF
–
pins covers the entire range
from GND to V
CC
. For correct converter operation, the
REF
+
pin must always be more positive than the REF
–
pin.
The LTC2433-1 can accept a differential reference voltage
from 0.1V to V
CC
. The converter output noise is deter-
mined by the thermal noise of the front-end circuits, and
as such, its value in microvolts is nearly constant with
reference voltage. A decrease in reference voltage will
significantly improve the converter’s effective resolution,
since the thermal noise (1.45
μ
V) is well below the quan-
tization level of the device (75.6
μ
V for a 5V reference). At
the minimum reference (100mV) the thermal noise
remains constant at 1.45
μ
V RMS (or 8.7
μ
V
P-P
), while the
quantization is reduced to 1.5
μ
V per LSB. As a result,
lowering the reference improves the effective resolution
for low level input voltages.
Input Voltage Range
The analog input is truly differential with an absolute/
common mode range for the IN
+
and IN
–
input pins
extending from GND – 0.3V to V
CC
+ 0.3V. Outside these
limits, the ESD protection devices begin to turn on and the
errors due to input leakage current increase rapidly. Within
these limits, the LTC2433-1 converts the bipolar differen-
tial input signal, V
IN
= IN
+
– IN
–
, from –FS = –0.5 V
REF
to
+FS = 0.5 V
REF
where V
REF
= REF
+
– REF
–
. Outside this
range, the converter indicates the overrange or the
underrange condition using distinct output codes.
Input signals applied to the analog input pins may extend
by 300mV below ground and above V
CC
. In order to limit
any fault current, resistors of up to 5k may be added in
series with the pins without affecting the performance of
the device. In the physical layout, it is important to main-
tain the parasitic capacitance of the connection between
these series resistors and the corresponding pins as low
as possible; therefore, the resistors should be located as
close as practical to the pins. The effect of the series
resistance on the converter accuracy can be evaluated
from the curves presented in the Input Current/Reference
Current sections. In addition, series resistors will intro-
duce a temperature dependent offset error due to the input
leakage current. A 10nA input leakage current will develop
a 1LSB offset error on an 8k resistor if V
REF
= 5V. This error
has a very strong temperature dependency.
Output Data Format
The LTC2433-1 serial output data stream is 19 bits long.
The first 3 bits represent status information indicating the
conversion state and sign. The next 16 bits are the conver-
sion result, MSB first. The third and fourth bit together are
also used to indicate an underrange condition (the differ-
ential input voltage is below –FS) or an overrange condi-
tion (the differential input voltage is above +FS).
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2433-1IMS | Differential Input 16-Bit No Latency DS ADC |
| LTC1043CS | Dual Precision Intrumentation Switched-Capacitor Building Block |
| LTC1043CN | Dual Precision Intrumentation Switched-Capacitor Building Block |
| LTC1043 | CAP., 22 MFD, 50V, ELECT., R |
| LTC1043C | Dual Precision Intrumentation Switched-Capacitor Building Block |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2433-1CMS#PBF | 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2433-1CMS#TR | 功能描述:IC CONV A/D 16BIT DIFF 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2433-1CMS#TRPBF | 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2433-1CMSPBF | 制造商:Linear Technology 功能描述:ADC,LTC2433 16bit diff D-S SPI MSOP |
| LTC2433-1IMS | 功能描述:IC CONV A/D 16BIT DIFF 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
發布緊急采購，3分鐘左右您將得到回復。