- 您現在的位置：買賣IC網 > PDF目錄10324 > LTC2431IMS#TR (Linear Technology)IC ADC 20BIT DIFFINPUT/REF10MSOP PDF資料下載
參數資料
| 型號： | LTC2431IMS#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 6/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 20BIT DIFFINPUT/REF10MSOP |
| 標準包裝： | 2,500 |
| 位數： | 20 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 1mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
| 配用： | DC586A-ND - BOARD DELTA SIGMA ADC LTC2431 |
| 其它名稱： | LTC2431IMSTR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC2430/LTC2431
14
24301f
+FS, the conversion result is clamped to the value corre-
sponding to the +FS + 1LSB. For differential input voltages
below –FS, the conversion result is clamped to the value
corresponding to –FS – 1LSB.
Frequency Rejection Selection (FO)
The LTC2430/LTC2431 internal oscillator provides better
than 110dB normal mode rejection at the line frequency
and all its harmonics for 50Hz
±2% or 60Hz ±2%. For
60Hz rejection, FO should be connected to GND while for
50Hz rejection the FO pin should be connected to VCC.
The selection of 50Hz or 60Hz rejection can also be made
by driving FO to an appropriate logic level. A selection
change during the sleep or data output states will not
disturb the converter operation. If the selection is made
during the conversion state, the result of the conversion in
progress may be outside specifications but the following
conversions will not be affected.
When a fundamental rejection frequency different from
50Hz or 60Hz is required or when the converter must be
synchronized with an outside source, the LTC2430 or
LTC2431 can operate with an external conversion clock.
The converter automatically detects the presence of an
external clock signal at the FO pin and turns off the internal
oscillator. The frequency fEOSC of the external signal must
be at least 5kHz to be detected. The external clock signal
duty cycle is not significant as long as the minimum and
maximum specifications for the high and low periods tHEO
and tLEO are observed.
While operating with an external conversion clock of a
frequency fEOSC, the LTC2430 or LTC2431 provides better
than 110dB normal mode rejection in a frequency range
fEOSC/2560 ±4% and its harmonics. The normal mode
rejection as a function of the input frequency deviation
from fEOSC/2560 is shown in Figure 4.
Whenever an external clock is not present at the FO pin, the
converter (LTC2430 or LTC2431) automatically activates
its internal oscillator and enters the Internal Conversion
Clock mode. Its operation will not be disturbed if the
change of conversion clock source occurs during the
sleep state or during the data output state while the con-
verter uses an external serial clock. If the change occurs
during the conversion state, the result of the conversion in
progress may be outside specifications but the following
conversions will not be affected. If the change occurs
during the data output state and the converter is in the
Internal SCK mode, the serial clock duty cycle may be
affected but the serial data stream will remain valid.
Table 3 summarizes the duration of each state and the
achievable output data rate as a function of FO.
SERIAL INTERFACE PINS
The LTC2430/LTC2431 transmit the conversion results
and receives the start of conversion command through a
synchronous 3-wire interface. During the conversion and
sleep states, this interface can be used to assess the
converter status and during the data output state it is used
to read the conversion result.
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK is used to synchro-
nize the data transfer. Each bit of data is shifted out the
SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the converter (LTC2430 or LTC2431) creates
its own serial clock by dividing the internal conversion clock
by 8. In the External SCK mode of operation, the SCK pin
is used as input. The internal or external SCK mode is
selected on power-up and then reselected every time a
HIGH-to-LOW transition is detected at the CS pin. If SCK
Figure 4. LTC2430/LTC2431 Normal Mode Rejection When
Using an External Oscillator of Frequency fEOSC
APPLICATIO S I FOR ATIO
WU
UU
DIFFERENTIAL INPUT SIGNAL FREQUENCY
DEVIATION FROM NOTCH FREQUENCY fEOSC/2560(%)
–12
–8
–4
048
12
NORMAL
MODE
REJECTION
(dB)
2431 F04
–80
–85
–90
–95
–100
–105
–110
–115
–120
–125
–130
–135
–140
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484E8F98SALC | CONN HSG PLUG 3POS STRGHT SCKT |
| VE-23B-IU-S | CONVERTER MOD DC/DC 95V 200W |
| VE-B34-IX-B1 | CONVERTER MOD DC/DC 48V 75W |
| VE-210-IU-S | CONVERTER MOD DC/DC 5V 200W |
| LTC2439-1CGN#PBF | IC ADC 16BIT 16CH MCRPWR 28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2433-1CMS | 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2433-1CMS#PBF | 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2433-1CMS#TR | 功能描述:IC CONV A/D 16BIT DIFF 10-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2433-1CMS#TRPBF | 功能描述:IC ADC DIFF 16BIT 3WIRE 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2433-1CMSPBF | 制造商:Linear Technology 功能描述:ADC,LTC2433 16bit diff D-S SPI MSOP |
發布緊急采購，3分鐘左右您將得到回復。