參數資料
型號: LTC2414IGN#TRPBF
廠商: Linear Technology
文件頁數: 24/48頁
文件大?。?/td> 0K
描述: IC ADC 8CH 24BIT DIFFINPUT28SSOP
標準包裝: 2,500
位數: 24
采樣率(每秒): 7.5
數據接口: MICROWIRE?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 1mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 28-SSOP
包裝: 帶卷 (TR)
輸入數目和類型: 8 個單端,單極;8 個單端,雙極;4 個差分,單極;4 個差分,雙極
LTC2414/LTC2418
30
241418fa
In addition to this gain error, the converter INL perfor-
mance is degraded by the reference source impedance.
When FO = LOW (internal oscillator and 60Hz notch), every
100
of source resistance driving REF+ or REFtranslates
into about 1.34ppm additional INL error. When FO = HIGH
(internal oscillator and 50Hz notch), every 100
of source
resistance driving REF+ or REFtranslates into about
1.1ppm additional INL error. When FO is driven by an
external oscillator with a frequency fEOSC, every 100 of
source resistance driving REF+ or REFtranslates into
about 8.73 10–6 fEOSCppm additional INL error.
Figure 22 shows the typical INL error due to the source
resistance driving the REF+ or REFpins when large CREF
values are used. The effect of the source resistance on the
two reference pins is additive with respect to this INL error.
In general, matching of source impedance for the REF+
and REFpins does not help the gain or the INL error. The
user is thus advised to minimize the combined source
impedance driving the REF+ and REFpins rather than to
try to match it.
The magnitude of the dynamic reference current depends
upon the size of the very stable internal sampling capaci-
tors and upon the accuracy of the converter sampling
clock. The accuracy of the internal clock over the entire
temperature and power supply range is typical better than
0.5%. Such a specification can also be easily achieved by
an external clock. When relatively stable resistors
(50ppm/
°C) are used for the external source impedance
seen by REF+ and REF, the expected drift of the dynamic
current gain error will be insignificant (about 1% of its
value over the entire temperature and voltage range). Even
for the most stringent applications a onetime calibration
operation may be sufficient.
In addition to the reference sampling charge, the reference
pins ESD protection diodes have a temperature dependent
leakage current. This leakage current, nominally 1nA
(
±10nA max), results in a small gain error. A 100 source
resistance will create a 0.05
V typical and 0.5V maxi-
mum full-scale error.
Output Data Rate
When using its internal oscillator, the LTC2414/LTC2418
can produce up to 7.5 readings per second with a notch
frequency of 60Hz (FO = LOW) and 6.25 readings per
second with a notch frequency of 50Hz (FO = HIGH). The
actual output data rate will depend upon the length of the
sleep and data output phases which are controlled by the
user and which can be made insignificantly short. When
operated with an external conversion clock (FO connected
to an external oscillator), the LTC2414/LTC2418 output
data rate can be increased as desired up to that determined
by the maximum fEOSC frequency of 2000kHz. The dura-
tion of the conversion phase is 20510/fEOSC. If fEOSC =
153600Hz, the converter behaves as if the internal oscil-
lator is used and the notch is set at 60Hz. There is no
significant difference in the LTC2414/LTC2418 perfor-
mance between these two operation modes.
An increase in fEOSC over the nominal 153600Hz will
translate into a proportional increase in the maximum
output data rate. This substantial advantage is neverthe-
less accompanied by three potential effects, which must
be carefully considered.
First, a change in fEOSC will result in a proportional change
in the internal notch position and in a reduction of the
converter differential mode rejection at the power line
frequency. In many applications, the subsequent perfor-
mance degradation can be substantially reduced by rely-
ing upon the LTC2414/LTC2418’s exceptional common
APPLICATIO S I FOR ATIO
WU
UU
Figure 22. INL vs Differential Input Voltage (VIN = IN+ – IN)
and Reference Source Resistance (RSOURCE at REF+ and REFfor
Large CREF Values (CREF ≥ 1F)
VINDIF/VREFDIF
–0.5 –0.4–0.3–0.2–0.1 0
0.1 0.2 0.3 0.4 0.5
INL
(ppm
OF
V
REF
)
15
12
9
6
3
0
–3
–6
–9
–12
–15
VCC = 5V
REF+ = 5V
REF– = GND
VINCM = 0.5 (IN
+ + IN) = 2.5V
FO = GND
CREF = 10F
TA = 25°C
RSOURCE = 1000
RSOURCE = 500
RSOURCE = 100
2414/18 F22
相關PDF資料
PDF描述
MAX9777ETI+T IC AMP AUDIO PWR 2.6W AB 28TQFN
D38999/20KE6SNLC CONN HSG RCPT 6POS WALL MT SCKT
MS27473T24B4SCLC CONN HSG PLUG 56POS STRGHT SCKT
LTC2414IGN#TR IC ADC 8CH 24BIT DIFFINPUT28SSOP
MS27473T24B4SBLC CONN HSG PLUG 56POS STRGHT SCKT
相關代理商/技術參數
參數描述
LTC2415-1CGN 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2415-1CGN#PBF 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2415-1CGN#TR 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2415-1CGN#TRPBF 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2415-1IGN 功能描述:IC ADC 24BIT DIFFINPUT/REF16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極