- 您現在的位置：買賣IC網 > PDF目錄39420 > LTC2392ILX-16#PBF (LINEAR TECHNOLOGY CORP) SUCCESSIVE APPROXIMATION ADC, PQFP48 PDF資料下載
參數資料
| 型號： | LTC2392ILX-16#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | SUCCESSIVE APPROXIMATION ADC, PQFP48 |
| 封裝： | 7 X 7 MM, LEAD FREE, PLASTIC, MS-026, QFN-48 |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 285K |
| 代理商： | LTC2392ILX-16#PBF |
LTC2392-16
239216f
applications inFormation
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high imped-
ance inputs of the LTC2392-16 without gain error. A high
impedance source should be buffered to minimize settling
time during acquisition and to optimize the distortion
performance of the ADC.
For best performance, a buffer amplifier should be used
to drive the analog inputs of the LTC2392-16. The am-
plifier provides low output impedance to allow for fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the ADC inputs which draw a small current spike during
acquisition.
Input Filtering
The noise and distortion of the buffer amplifier and other
circuitry must be considered since they add to the ADC
noiseanddistortion.Noisyinputcircuitryshouldbefiltered
prior to the analog inputs to minimize noise. A simple
1-pole RC filter is sufficient for many applications.
Large filter RC time constants slow down the settling at
the analog inputs. It is important that the overall RC time
constants be short enough to allow the analog inputs to
completely settle to 16-bit resolution within the acquisi-
tion time (tACQ).
High quality capacitors and resistors should be used in the
RC filter since these components can add distortion. NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occurduringsoldering.Metalfilmsurfacemountresistors
are much less susceptible to both problems.
Single-to-Differential Conversion
For single-ended input signals, a single-ended-to-dif-
ferential conversion circuit must be used to produce a
differential signal at the ADC inputs. The LT6350 ADC
driver is recommended for performing a single-ended-
to-differential conversion, as shown in Figure 4a. Its low
noiseandgoodDClinearityallowstheLTC2392-16tomeet
full data sheet specifications. An alternative solution using
two op amps is shown in Figure 4b. Using two LT1806 op
amps,thecircuitachieves94dBsignal-to-noiseratio(SNR).
For a 20kHz input signal, the input of the LTC2392-16 has
been bandwidth limited to about 25kHz.
ADC REFERENCE
A low noise, low temperature drift reference is critical to
achieving the full datasheet performance of the ADC. The
LTC2392-16 provides an excellent internal reference with
a ±20ppm/°C (max) temperature coefficient. For better
accuracy, an external reference can be used.
The high speed, low noise internal reference buffer is used
for both internal and external reference applications. It
cannot be bypassed.
Figure 4a. Recommended Single-Ended-to-Differential
Conversion Circuit Using the LT6350 ADC Driver
Figure 4b. Alternative Single-Ended-to-Differential
Conversion Circuit Using Two LT1806 Op Amps
249
301
ANALOG
INPUT
0V TO 4.096V
COMMON
MODE
VOLTAGE
301
0.013F
LTC2392-16
239216 F04b
IN+
IN–
–
+
LT1806
–
+
LT1806
249
ANALOG INPUT
0V TO 4.096V
SINGLE-ENDED-
TO-DIFFERENTIAL
DRIVER
249
2200pF
LTC2392-16
239216 F04a
IN+
IN–
LT6350
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2392IUK-16#PBF | SUCCESSIVE APPROXIMATION ADC, PQCC48 |
| LTC2392IUK-16#TRPBF | SUCCESSIVE APPROXIMATION ADC, PQCC48 |
| LTC2448IUHF | 16-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PQCC38 |
| LTC2451CTS8B#TRMPBF | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO8 |
| LTC2451ITSB#TRMPBF | 1-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2392IUK-16#PBF | 功能描述:IC ADC 16B SER/PAR 500K 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2392IUK-16#TRPBF | 功能描述:IC ADC 16B SER/PAR 500K 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2393CLX-16#PBF | 功能描述:IC ADC 16BIT SER/PAR 1M 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2393CLX-16#PBF | 制造商:Linear Technology 功能描述:ANALOG TO DIGITAL (A/D) CONVERTER IC |
| LTC2393CUK-16#PBF | 功能描述:IC ADC 16BIT SER/PAR 1M 48-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。