參數資料
型號： LTC2285CUP#PBF
廠商： Linear Technology
文件頁數： 10/24頁
文件大?。?/td> 0K
描述： IC ADC DUAL 14BIT 125MSPS 64QFN
標準包裝： 40
位數： 14
采樣率（每秒）： 125M
數據接口： 并聯
轉換器數目： 2
功率耗散（最大）： 915mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 64-WFQFN 裸露焊盤
供應商設備封裝： 64-QFN（9x9）
包裝： 管件
輸入數目和類型： 2 個單端，雙極; 2 個差分, 雙極
LTC2285
18
2285fb
APPLICATIONS INFORMATION
Table 2. MODE Pin Function
MODE PIN
OUTPUT FORMAT
CLOCK DUTY
CYCLE STABILIZER
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
Overow Bit
When OF outputs a logic high the converter is either
overranged or underranged on channel A or channel B.
Note that both channels share a common OF pin, which
is not the case for slower pin compatible parts such as
the LTC2284 or LTC2299. OF is disabled when channel A
is in sleep or nap mode.
Output Clock
The ADC has a delayed version of the CLKB input available
as a digital output, CLKOUT. The falling edge of the CLKOUT
pin can be used to latch the digital output data. CLKOUT
is disabled when channel B is in sleep or nap mode.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven.
For example, if the converter is driving a DSP powered
by a 1.8V supply, then OVDD should be tied to that same
1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND
up to 1V and must be less than OVDD. The logic outputs
will swing between OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin,
OE. OE high disables all data outputs including OF. The
data access and bus relinquish times are too slow to
allow the outputs to be enabled and disabled during full
speed operation. The output Hi-Z state is intended for use
during long periods of inactivity. Channels A and B have
independent output enable pins (OEA, OEB).
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes to
conservepower.ConnectingSHDNtoGNDresultsinnormal
operation. Connecting SHDN to VDD and OE to VDD results
in sleep mode, which powers down all circuitry including
the reference and typically dissipates 1mW. When exiting
sleep mode it will take milliseconds for the output data
to become valid because the reference capacitors have to
recharge and stabilize. Connecting SHDN to VDD and OE
to GND results in nap mode, which typically dissipates
30mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that
from sleep mode, typically taking 100 clock cycles. In both
sleep and nap modes, all digital outputs are disabled and
enter the Hi-Z state.
Channels A and B have independent SHDN pins (SHDNA,
SHDNB). Channel A is controlled by SHDNA and OEA,
and channel B is controlled by SHDNB and OEB. The
nap, sleep and output enable modes of the two channels
are completely independent, so it is possible to have one
channel operating while the other channel is in nap or
sleep mode.
Digital Output Multiplexer
The digital outputs of the LTC2285 can be multiplexed
onto a single data bus if the sample rate is 80Msps or
less. The MUX pin is a digital input that swaps the two
data busses. If MUX is High, channel A comes out on
DA0-DA13; channel B comes out on DB0-DB13. If MUX is
Low, the output busses are swapped and channel A comes
out on DB0-DB13; channel B comes out on DA0-DA13.
To multiplex both channels onto a single output bus,
connect MUX, CLKA and CLKB together (see the Timing
Diagram for the multiplexed mode). The multiplexed data
is available on either data bus—the unused data bus can
be disabled with its OE pin.
Grounding and Bypassing
The LTC2285 requires a printed circuit board with a clean,
unbroken ground plane. A multilayer board with an internal
ground plane is recommended. Layout for the printed
circuit board should ensure that digital and analog signal
lines are separated as much as possible. In particular, care
相關PDF資料
PDF描述
LTC2289IUP#PBF IC ADC DUAL 10BIT 80MSPS 64QFN
LTC2290IUP#TRPBF IC ADC DUAL 12BIT 10MSPS 64QFN
LTC2298IUP#PBF IC ADC DUAL 14BIT 65MSPS 64QFN
LTC2305CDE#TRPBF IC ADC 12-BIT 2CHN 12-DFN
LTC2306CDD#PBF IC ADC 12BIT 2CH 500KSPS 10-DFN
相關代理商/技術參數
參數描述
LTC2285CUP-TR 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 14-Bit, 125Msps Low Power 3V ADC
LTC2285CUP-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 14-Bit, 125Msps Low Power 3V ADC
LTC2285IUP 制造商:Linear Technology 功能描述:ADC Dual Pipelined 125Msps 14-bit Parallel 64-Pin QFN EP
LTC2285IUP#PBF 功能描述:IC ADC DUAL 14BIT 125MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2285IUP#TRPBF 功能描述:IC ADC DUAL 14BIT 125MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*