- 您現在的位置：買賣IC網 > PDF目錄2005 > LTC2262IUJ-12#PBF (Linear Technology)IC ADC 12BIT 150MSPS 40-QFN PDF資料下載
參數資料
| 型號： | LTC2262IUJ-12#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 150MSPS 40-QFN |
| 產品培訓模塊： | LTC2262 - Ultra Low Power High Speed ADCs |
| 標準包裝： | 61 |
| 位數： | 12 |
| 采樣率（每秒）： | 150M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 146mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN（6x6） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分 |
| 配用： | DC890B-ND - BOARD USB DATA COLLECTION |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2262-12
20
226212fc
For more information www.linear.com/LTC2262-12
The digital output is decoded at the receiver by inverting
the odd bits (D1, D3, D5, D7, D9, D11). The alternate bit
polaritymodeisindependentofthedigitaloutputrandom-
izer—either,bothorneitherfunctioncanbeonatthesame
time. When alternate bit polarity mode is on, the data
format is offset binary and the 2’s complement control bit
has no effect. The alternate bit polarity mode is enabled
by serially programming mode control register A4.
Digital Output Test Patterns
To allow in-circuit testing of the digital interface to the
A/D, there are several test modes that force the A/D data
outputs (OF, D11-D0) to known values:
All 1s: All outputs are 1
All 0s: All outputs are 0
Alternating: Outputs change from all 1s to all 0s on
alternating samples
Checkerboard: Outputs change from 1010101010101
to 0101010101010 on alternating samples
The digital output test patterns are enabled by serially
programming mode control register A4. When enabled,
the test patterns override all other formatting modes: 2’s
complement, randomizer, alternate-bit-polarity.
Output Disable
The digital outputs may be disabled by serially program-
mingmodecontrolregisterA3.Alldigitaloutputsincluding
OFandCLKOUTaredisabled.Thehighimpedancedisabled
state is intended for long periods of inactivity—it is too
slow to multiplex a data bus between multiple converters
at full speed.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire A/D converter is powered
down,resultingin0.5mWpowerconsumption.Sleepmode
is enabled by mode control register A1 (serial program-
ming mode), or by SDI (parallel programming mode).
The amount of time required to recover from sleep mode
depends on the size of the bypass capacitors on VREF,
REFH, and REFL. For the suggested values in Figure 8,
the A/D will stabilize after 2ms.
In nap mode the A/D core is powered down while the
internal reference circuits stay active, allowing faster
wake-up than from sleep mode. Recovering from nap
mode requires at least 100 clock cycles. If the application
demands very accurate DC settling then an additional
50s should be allowed so the on-chip references can
settle from the slight temperature shift caused by the
change in supply current as the A/D leaves nap mode.
Nap mode is enabled by mode control register A1 in the
serial programming mode.
DEVICE PROGRAMMING MODES
The operating modes of the LTC2262-12 can be pro-
grammed by either a parallel interface or a simple serial
interface. The serial interface has more flexibility and
can program all available modes. The parallel interface
is more limited and can only program some of the more
commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK and SDI pins are binary logic
inputs that set certain operating modes. These pins can
be tied to VDD or ground, or driven by 1.8V, 2.5V or 3.3V
CMOS logic. Table 2 shows the modes set by CS, SCK
and SDI.
Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
Clock Duty Cycle Stabilizer Control Bit
0 = Clock Duty Cycle Stabilizer Off
1 = Clock Duty Cycle Stabilizer On
SCK
Digital Output Mode Control Bit
0 = Full-Rate CMOS Output Mode
1 = Double Data Rate LVDS Output Mode
(3.5mA LVDS Current, Internal Termination Off)
SDI
Power Down Control Bit
0 = Normal Operation
1 = Sleep Mode
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2264CUJ-12#PBF | IC ADC 12BIT SER/PAR 40M 40-QFN |
| LTC2268IUJ-14#TRPBF | IC ADC 14BIT 125MSPS DUAL 40QFN |
| LTC2280CUP#PBF | IC ADC DUAL 10BIT 105MSPS 64-QFN |
| LTC2281IUP#PBF | IC ADC 10BIT DUAL 64-QFN |
| LTC2282CUP#PBF | IC ADC DUAL 12BIT 105MSPS 64-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2262IUJ-14#PBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 150Msps 14-bit Parallel/LVDS 40-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 14BIT 1.8V 150MSPS 40-QFN |
| LTC2262IUJ-14#TRPBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 150Msps 14-bit Parallel/LVDS 40-Pin QFN EP T/R 制造商:Linear Technology 功能描述:IC ADC 14BIT 150MSPS 40-QFN |
| LTC2263-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs |
| LTC2263-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad 14-Bit, 125Msps ADC with Integrated Drivers |
| LTC2263CUJ-12#PBF | 功能描述:IC ADC 12BIT SER/PAR 25M 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。