- 您現在的位置：買賣IC網 > PDF目錄10124 > LTC2257IUJ-14#TRPBF (Linear Technology)IC ADC 14BIT 40MSPS 1.8V 40-QFN PDF資料下載
參數資料
| 型號： | LTC2257IUJ-14#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 40MSPS 1.8V 40-QFN |
| 產品培訓模塊： | LTC2262 - Ultra Low Power High Speed ADCs |
| 標準包裝： | 2,000 |
| 位數： | 14 |
| 采樣率（每秒）： | 40M |
| 數據接口： | 并聯，串行，SPI |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 54mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN（6x6） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分 |
| 配用： | DC718C-ND - DEMO QUIKEVAL-II DATA |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
15
225814fc
LTC2258-14
LTC2257-14/LTC2256-14
For more information www.linear.com/LTC2258-14
pin FuncTions
PINS THAT ARE THE SAME FOR ALL DIGITAL OUTPUT
MODES
AIN+ (Pin 1): Positive Differential Analog Input.
AIN– (Pin 2): Negative Differential Analog Input.
GND (Pin 3): ADC Power Ground.
REFH (Pins 4, 5): ADC High Reference. Bypass to Pins
6, 7 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
REFL (Pins 6, 7): ADC Low Reference. Bypass to Pins
4, 5 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
PAR/SER (Pin 8): Programming Mode Selection Pin. Con-
nect to ground to enable the serial programming mode.
CS, SCK, SDI, SDO become a serial interface that control
the A/D operating modes. Connect to VDD to enable the
parallel programming mode where CS, SCK, SDI become
parallel logic inputs that control a reduced set of the A/D
operating modes. PAR/SER should be connected directly
to ground or the VDD of the part and not be driven by a
logic signal.
VDD (Pins 9, 10, 40): 1.8V Analog Power Supply. Bypass
to ground with 0.1F ceramic capacitors. Pins 9 and 10
can share a bypass capacitor.
ENC+ (Pin 11): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 12): Encode Complement Input. Conversion
starts on the falling edge.
CS (Pin 13): In serial programming mode, (PAR/SER =
0V), CS is the serial interface chip select input. When
CS is low, SCK is enabled for shifting data on SDI into
the mode control registers. In the parallel programming
mode (PAR/SER = VDD), CS controls the clock duty cycle
stabilizer. When CS is low, the clock duty cycle stabilizer is
turned off. When CS is high, the clock duty cycle stabilizer
is turned on. CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 14): In serial programming mode, (PAR/SER
= 0V), SCK is the serial interface clock input. In the
parallel programming mode (PAR/SER = VDD), SCK
controls the digital output mode. When SCK is low,
the full-rate CMOS output mode is enabled. When SCK
is high, the double data rate LVDS output mode (with
3.5mA output current) is enabled. SCK can be driven
with 1.8V to 3.3V logic.
SDI (Pin 15): In serial programming mode, (PAR/SER =
0V), SDI is the serial interface data input. Data on SDI is
clocked into the mode control registers on the rising edge
of SCK. In the parallel programming mode (PAR/SER =
VDD), SDI can be used to power down the part. When SDI
is low, the part operates normally. When SDI is high, the
part enters sleep mode. SDI can be driven with 1.8V to
3.3V logic.
SDO (Pin 16): In serial programming mode, (PAR/SER
= 0V), SDO is the optional serial interface data output.
Data on SDO is read back from the mode control registers
and can be latched on the falling edge of SCK. SDO is an
open-drain NMOS output that requires an external 2k
pull-up resistor to 1.8V-3.3V. If read back from the mode
control registers is not needed, the pull-up resistor is not
necessary and SDO can be left unconnected. In the parallel
programming mode (PAR/SER = VDD), SDO is not used
and should not be connected.
OGND (Pin 25): Output Driver Ground.
OVDD (Pin 26): Output Driver Supply. Bypass to ground
with a 0.1F ceramic capacitor.
VCM (Pin 37): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs. Bypass to ground with a 0.1F
ceramic capacitor.
VREF(Pin38):ReferenceVoltageOutput,Nominally1.25V.
Bypass to ground with a 1F ceramic capacitor.
SENSE(Pin39):ReferenceProgrammingPin.Connecting
SENSEtoVDDselectstheinternalreferenceanda±1Vinput
range. Connecting SENSE to ground selects the internal
reference and a ±0.5V input range. An external reference
between 0.625V and 1.3V applied to SENSE selects an
input range of ±0.8 VSENSE.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7202LA15JGI | IC FIFO ASYNCH 1KX9 15NS 32PLCC |
| MS3102R32-3S | CONN RCPT 9POS BOX MNT W/SCKT |
| LTC1609ACSW#TRPBF | IC ADC SRL 16BIT 200KSPS 20-SOIC |
| VI-2NH-MX-F3 | CONVERTER MOD DC/DC 52V 75W |
| LTC1609ACSW#PBF | IC ADC SRL 16BIT 200KSPS 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2257UJ-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
| LTC2257UJ-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
| LTC2258-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
| LTC2258-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
| LTC2258CUJ-12#PBF | 功能描述:IC ADC 12BIT 65MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。