- 您現在的位置：買賣IC網 > PDF目錄10208 > LTC2256IUJ-12#PBF (Linear Technology)IC ADC 12BIT 25MSPS 1.8V 40-QFN PDF資料下載
參數資料
| 型號： | LTC2256IUJ-12#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 18/34頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 25MSPS 1.8V 40-QFN |
| 產品培訓模塊： | LTC2262 - Ultra Low Power High Speed ADCs |
| 標準包裝： | 61 |
| 位數： | 12 |
| 采樣率（每秒）： | 25M |
| 數據接口： | 并聯，串行，SPI |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 38mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-QFN（6x6） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分 |
| 配用： | DC718C-ND - DEMO QUIKEVAL-II DATA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LTC2258-12
LTC2257-12/LTC2256-12
25
225812fd
For more information www.linear.com/LTC2258-12
The digital output is decoded at the receiver by inverting
the odd bits (D1, D3, D5, D7, D9, D11). The alternate
bit polarity mode is independent of the digital output
randomizer—either, both or neither function can be on
at the same time. When alternate bit polarity mode is on,
the data format is offset binary and the 2’s complement
control bit has no effect. The alternate bit polarity mode is
enabledbyseriallyprogrammingmodecontrolregisterA4.
Digital Output Test Patterns
To allow in-circuit testing of the digital interface to the
A/D, there are several test modes that force the A/D data
outputs (OF, D11-D0) to known values:
All 1s: All outputs are 1
All 0s: All outputs are 0
Alternating: Outputs change from all 1s to all 0s on
alternating samples
Checkerboard: Outputs change from 1010101010101
to 0101010101010 on alternating samples
The digital output test patterns are enabled by serially
programming mode control register A4. When enabled,
the test patterns override all other formatting modes: 2’s
complement, randomizer, alternate-bit-polarity.
Output Disable
The digital outputs may be disabled by serially program-
mingmodecontrolregisterA3.Alldigitaloutputsincluding
OFandCLKOUTaredisabled.Thehighimpedancedisabled
state is intended for long periods of inactivity—it is too
slow to multiplex a data bus between multiple converters
at full speed.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire A/D converter is powered
down,resultingin0.5mWpowerconsumption.Sleepmode
is enabled by mode control register A1 (serial program-
ming mode), or by SDI (parallel programming mode).
The amount of time required to recover from sleep mode
depends on the size of the bypass capacitors on VREF,
REFH, and REFL. For the suggested values in Figure 8,
the A/D will stabilize after 2ms.
InnapmodetheA/Dcoreispowereddownwhiletheinternal
referencecircuitsstayactive,allowingfasterwake-upthan
from sleep mode. Recovering from nap mode requires at
least 100 clock cycles. If the application demands very
accurate DC settling then an additional 50s should be
allowedsotheon-chipreferencescansettlefromtheslight
temperature shift caused by the change in supply current
as the A/D leaves nap mode. Nap mode is enabled by mode
control register A1 in the serial programming mode.
DEVICE PROGRAMMING MODES
The operating modes of the LTC2258-12/LTC2257-12/
LTC2256-12 can be programmed by either a parallel
interface or a simple serial interface. The serial interface
has more flexibility and can program all available modes.
Theparallelinterfaceismorelimitedandcanonlyprogram
some of the more commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK and SDI pins are binary logic
inputs that set certain operating modes. These pins can
be tied to VDD or ground, or driven by 1.8V, 2.5V or 3.3V
CMOS logic. Table 2 shows the modes set by CS, SCK
and SDI.
Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
Clock Duty Cycle Stabilizer Control Bit
0 = Clock Duty Cycle Stabilizer Off
1 = Clock Duty Cycle Stabilizer On
SCK
Digital Output Mode Control Bit
0 = Full-Rate CMOS Output Mode
1 = Double Data Rate LVDS Output Mode
(3.5mA LVDS Current, Internal Termination Off)
SDI
Power Down Control Bit
0 = Normal Operation
1 = Sleep Mode
applicaTions inForMaTion
相關PDF資料 |
PDF描述 |
|---|---|
| EN3P12F26SX | CONN RCPT 12POS FEMALE PANEL #26 |
| VI-21D-IU-F2 | CONVERTER MOD DC/DC 85V 200W |
| SP3078EMN-L/TR | IC TXRX RS485/RS422 ESD 8NSOIC |
| AD7492ARZ | IC ADC 12BIT PAR 1MSPS 24SOIC |
| MS3126E12-8SW | CONN PLUG 8POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2256IUJ-12-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 65/40/2 5Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-14#PBF | 功能描述:IC ADC 14BIT 25MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2256IUJ-14#TRPBF | 功能描述:IC ADC 14BIT 25MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2256IUJ-14-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
| LTC2256IUJ-14-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs |
發布緊急采購，3分鐘左右您將得到回復。