- 您現在的位置：買賣IC網 > PDF目錄39414 > LTC2246HLU (LINEAR TECHNOLOGY CORP) 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32 PDF資料下載
參數資料
| 型號： | LTC2246HLU |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32 |
| 封裝： | 5 X 5 MM, PLASTIC, MS-026, TQFP-32 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 273K |
| 代理商： | LTC2246HLU |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LTC2246H
14
2246hf
APPLICATIONS INFORMATION
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors
have to recharge and stabilize. Connecting SHDN to VDD
and OE to GND results in nap mode, which typically dis-
sipates 15mW. In nap mode, the on-chip reference circuit
is kept on, so that recovery from nap mode is faster than
that from sleep mode, typically taking 100 clock cycles. In
both sleep and nap modes, all digital outputs are disabled
and enter the Hi-Z state.
Grounding and Bypassing
The LTC2246H requires a printed circuit board with a clean,
unbroken ground plane. A multilayer board with an internal
ground plane is recommended. Layout for the printed
circuit board should ensure that digital and analog signal
lines are separated as much as possible. In particular, care
should be taken not to run any digital track alongside an
analog signal track or underneath the ADC.
High quality ceramic bypass capacitors should be used at
the VDD, OVDD, VCM, REFH, and REFL pins. Bypass capaci-
tors must be located as close to the pins as possible. Of
particular importance is the 0.1μF capacitor between REFH
and REFL. This capacitor should be placed as close to the
device as possible (1.5mm or less). A size 0402 ceramic
capacitor is recommended. The large 2.2μF capacitor be-
tween REFH and REFL can be somewhat further away. The
traces connecting the pins and bypass capacitors must be
kept short and should be made as wide as possible.
The LTC2246H differential inputs should run parallel and
close to each other. The input traces should be as short
as possible to minimize capacitance and to minimize
noise pickup.
Data Format
Using the MODE pin, the LTC2246H parallel digital output
can be selected for offset binary or 2’s complement format.
Connecting MODE to GND or 1/3VDD selects offset binary
output format. Connecting MODE to 2/3VDD or VDD selects
2’s complement output format.
An external resistor divider can be used to set the 1/3VDD
or 2/3VDD logic values. Table 2 shows the logic states for
the MODE pin.
Table 2. MODE Pin Function
MODE Pin
Output Format
Clock Duty
Cycle Stablizer
0
Offset Binary
Off
1/3VDD
Offset Binary
On
2/3VDD
2’s Complement
On
VDD
2’s Complement
Off
Overow Bit
When OF outputs a logic high the converter is either over-
ranged or underranged.
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven.
For example if the converter is driving a DSP powered
by a 1.8V supply, then OVDD should be tied to that same
1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND
up to 1V and must be less than OVDD. The logic outputs
will swing between OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin,
OE. OE high disables all data outputs including OF.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2246IUH | 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC32 |
| LTC2246IUH#TR | 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC32 |
| LTC2257CUJ-12#TRPBF | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC40 |
| LTC2256CUJ-12#PBF | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC40 |
| LTC2256CUJ-12#TRPBF | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2246HLU#PBF | 功能描述:IC ADC 14BIT 25MSPS 32-TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC2246HLX | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 25Msps 125°C ADC In LQFP |
| LTC2246HLX#PBF | 功能描述:IC ADC 14BIT 25MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2246HLX-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 25Msps 125°C ADC In LQFP |
| LTC2246HLX-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 25Msps 125°C ADC In LQFP |
發布緊急采購，3分鐘左右您將得到回復。