- 您現在的位置：買賣IC網 > PDF目錄10268 > LTC2239CUH#TRPBF (Linear Technology)IC ADC 10BIT 80MSPS 3V 32-QFN PDF資料下載
參數資料
| 型號： | LTC2239CUH#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 80MSPS 3V 32-QFN |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 246mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
13
LTC2239
2239fa
APPLICATIO S I FOR ATIO
WU
U
Single-Ended Input
For cost sensitive applications, the analog inputs can be
driven single-ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be
driven differentially. Each input should swing
±0.5V for
the 2V range or
±0.25V for the 1V range, around a
common mode voltage of 1.5V. The VCM output pin (Pin
31) may be used to provide the common mode bias level.
VCM can be tied directly to the center tap of a transformer
to set the DC input level or as a reference level to an op amp
differential driver circuit. The VCM pin must be bypassed to
ground close to the ADC with a 2.2
F or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the
dynamic performance of the LTC2239 can be influenced
by the input drive circuitry, particularly the second and
third harmonics. Source impedance and reactance can
influence SFDR. At the falling edge of CLK, the sample-
and-hold circuit will connect the 4pF sampling capacitor to
the input pin and start the sampling period. The sampling
period ends when CLK rises, holding the sampled input on
the sampling capacitor. Ideally the input circuitry should
be fast enough to fully charge the sampling capacitor
during the sampling period 1/(2FENCODE); however, this is
not always possible and the incomplete settling may
degrade the SFDR. The sampling glitch has been designed
to be as linear as possible to minimize the effects of
incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100
or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2239 being driven by an RF
transformer with a center tapped secondary. The second-
ary center tap is DC biased with VCM, setting the ADC input
signal at its optimum DC level. Terminating on the trans-
former secondary is desirable, as this provides a common
mode path for charging glitches caused by the sample and
hold. Figure 3 shows a 1:1 turns ratio transformer. Other
turns ratios can be used if the source impedance seen by
the ADC does not exceed 100
for each ADC input. A
disadvantage of using a transformer is the loss of low
frequency response. Most small RF transformers have
poor performance at frequencies below 1MHz.
Figure 4 demonstrates the use of a differential amplifier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides low
frequency input response; however, the limited gain band-
width of most op amps will limit the SFDR at high input
frequencies.
25
25
25
25
0.1
F
AIN
+
AIN
–
12pF
2.2
F
VCM
LTC2239
ANALOG
INPUT
0.1
FT1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
2239 F03
Figure 4. Differential Drive with an Amplifier
25
25
12pF
2.2
F
VCM
LTC2239
2239 F04
–
+
CM
ANALOG
INPUT
HIGH SPEED
DIFFERENTIAL
AMPLIFIER
AIN
+
AIN
–
Figure 3. Single-Ended to Differential Conversion
Using a Transformer
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9756ETX+ | IC AMP AUDIO PWR 2.3W AB 36TQFN |
| LTC2233CUK#TR | IC ADC 10BIT 80MSPS SAMPL 48QFN |
| MAX9760EUI+ | IC AMP AUDIO PWR 3W STER 28TSSOP |
| MAX9750AEUI+ | IC AMP AUDIO PWR 2.6W AB 28TSSOP |
| LTC1853CFW | IC A/D CONV 8CH 12BIT 48-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2239IUH | 制造商:LINER 制造商全稱:Linear Technology 功能描述:10-Bit, 80Msps Low Noise 3V ADC |
| LTC2239IUH#PBF | 功能描述:IC ADC 10-BIT 80MSPS 3V 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC2239IUH#TRPBF | 功能描述:IC ADC 10BIT 80MSPS 3V 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC2240-10 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit 250Msps/ 210Msps/170Msps ADCs |
| LTC2240-12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit 250Msps/ 210Msps/170Msps ADCs |
發布緊急采購，3分鐘左右您將得到回復。