- 您現在的位置：買賣IC網 > PDF目錄10088 > LTC2222CUK#TRPBF (Linear Technology)IC ADC 12BIT 105MSPS SAMPL 48QFN PDF資料下載
參數資料
| 型號： | LTC2222CUK#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 105MSPS SAMPL 48QFN |
| 標準包裝： | 2,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 105M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 535mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2222/LTC2223
18
22223fb
APPLICATIONS INFORMATION
Figure 4 demonstrates the use of a differential amplier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides
low frequency input response; however, the limited gain
bandwidth of most op amps will limit the SFDR at high
input frequencies.
Figure 5 shows a single-ended input circuit. The impedance
seen by the analog inputs should be matched. This circuit
is not recommended if low distortion is required.
The 25Ω resistors and 12pF capacitor on the analog inputs
serve two purposes: isolating the drive circuitry from
the sample-and-hold charging glitches and limiting the
wideband noise at the converter input. For input frequen-
cies higher than 100MHz, the capacitor may need to be
decreased to prevent excessive signal loss.
For input frequencies above 100MHz the input circuits of
Figure 6, 7 and 8 are recommended. The balun transformer
gives better high frequency response than a ux coupled
center tapped transformer. The coupling capacitors allow
the analog inputs to be DC biased at 1.6V. In Figure 8 the
series inductors are impedance matching elements that
maximize the ADC bandwidth.
Reference Operation
Figure 9 shows the LTC2222/LTC2223 reference circuitry
consisting of a 1.6V bandgap reference, a difference ampli-
er and switching and control circuit. The internal voltage
reference can be congured for two pin selectable input
ranges of 2V (±1V differential) or 1V (±0.5V differential).
Tying the SENSE pin to VDD selects the 2V range; typing
the SENSE pin to VCM selects the 1V range.
The 1.6V bandgap reference serves two functions: its
output provides a DC bias point for setting the common
mode voltage of any external input circuitry; additionally,
the reference is used with a difference amplier to gener-
ate the differential reference levels needed by the internal
ADC circuitry. An external bypass capacitor is required
for the 1.6V reference output, VCM. This provides a high
frequency low impedance path to ground for internal and
external circuitry.
The difference amplier generates the high and low
reference for the ADC. High speed switching circuits are
connected to these outputs and they must be externally
bypassed. Each output has four pins: two each of REFHA
and REFHB for the high reference and two each of REFLA
and REFLB for the low reference. The multiple output pins
are needed to reduce package inductance. Bypass capaci-
tors must be connected as shown in Figure 9.
Other voltage ranges in between the pin selectable ranges
can be programmed with two external resistors as shown
in Figure 10. An external reference can be used by ap-
plying its output directly or through a resistor divider to
SENSE. It is not recommended to drive the SENSE pin
with a logic device. The SENSE pin should be tied to the
appropriate level as close to the converter as possible. If
the SENSE pin is driven externally, it should be bypassed
to ground as close to the device as possible with a 1μF
ceramic capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| CS3106A-24-67PZ | CONN PLUG 19POS STRAIGHT W/PINS |
| IDT7283L12PA8 | IC MEM FIFO 2048X9 12NS 56-TSSOP |
| LTC2222CUK#TR | IC ADC 12BIT 105MSPS SAMPL 48QFN |
| LTC2222CUK#PBF | IC ADC 12BIT 105MSPS SAMPL 48QFN |
| LTC2222CUK | IC ADC 12BIT 105MSPS SAMPL 48QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2222IUK | 功能描述:IC ADC 12BIT 105MSPS SAMPL 48QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2222IUK#PBF | 功能描述:IC ADC 12BIT 105MSPS SAMPL 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2222IUK#TR | 功能描述:IC ADC 12BIT 105MSPS SAMPL 48QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2222IUK#TRPBF | 功能描述:IC ADC 12BIT 105MSPS SAMPL 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2222IUK-11 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:11-Bit, 105Msps ADC |
發布緊急采購，3分鐘左右您將得到回復。