- 您現(xiàn)在的位置：買賣IC網 > PDF目錄39411 > LTC2157IUP-14#TRPBF (LINEAR TECHNOLOGY CORP) 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 PDF資料下載
參數資料
| 型號： | LTC2157IUP-14#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| 封裝： | 9 X 9 MM, LEAD FREE, PLASTIC, MO-220WNJR-5, QFN-64 |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 647K |
| 代理商： | LTC2157IUP-14#TRPBF |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
13
21576514f
LTC2157-14/
LTC2156-14/LTC2155-14
PIN FUNCTIONS
VDD (Pins 1, 2, 15, 16, 17, 64): 1.8V Analog Power Supply.
Bypass to ground with 0.1μF ceramic capacitors. Pins 1,
2, 64 can share a bypass capacitor. Pins 15, 16, 17 can
share a bypass capacitor.
GND (Pins 3, 6, 9, 11, 14, 18, 21, 58, Exposed Pad
Pin 65): ADC Power Ground. The exposed pad must be
soldered to the PCB ground.
AINA+ (Pin 4): Positive Differential Analog Input for
Channel A.
AINA– (Pin 5): Negative Differential Analog Input for
Channel A.
SENSE (Pin 7): Reference Programming Pin. Connecting
SENSE to VDD selects the internal reference and a ±0.75V
input range. An external reference between 1.2V and 1.3V
applied to SENSE selects an input range of ±0.6 × VSENSE.
VREF (Pin 8): Reference Voltage Output. Bypass to ground
with a 2.2μF ceramic capacitor. Nominally 1.25V.
VCM (Pin 10): Common Mode Bias Output; nominally equal
to 0.435 VDD. VCM should be used to bias the common
mode of the analog inputs. Bypass to ground with a 0.1μF
ceramic capacitor.
AINB– (Pin 12): Negative Differential Analog Input for
Channel B.
AINB+ (Pin 13): Positive Differential Analog Input for
Channel B.
ENC+ (Pin 19):
Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 20):
Encode Complement Input. Conversion
starts on the falling edge.
OGND (Pins 33, 48): Output Driver Ground.
OVDD (Pins 32, 49): 1.8V Output Driver Supply. Bypass
each pin to ground with separate 0.1μF ceramic capacitors.
SDO (Pin 59): Serial Interface Data Output. In serial pro-
gramming mode, (PAR/SER = 0V), SDO is the optional serial
interface data output. Data on SDO is read back from the
mode control registers and can be latched on the falling
edge of SCK. SDO is an open-drain N-channel MOSFET
output that requires an external 2k pull-up resistor from
1.8V to 3.3V. If readback from the mode control registers
is not needed, the pull-up resistor is not necessary and
SDO can be left unconnected.
SDI (Pin 60): Serial Interface Data Input. In serial program-
ming mode, (PAR/SER = 0V), SDI is the serial interface
data input. Data on SDI is clocked into the mode control
registers on the rising edge of SCK. In the parallel pro-
gramming mode (PAR/SER = VDD), SDI selects 3.5mA or
1.75mA LVDS output current (see Table 2). SDI can be
driven with 1.8V to 3.3V logic.
SCK (Pin 61): Serial Interface Clock Input. In serial
programming mode, (PAR/SER = 0V), SCK is the serial
interface clock input. In the parallel programming mode
(PAR/SER = VDD), SCK can be used to place the part in the
low power sleep mode (see Table 2). SCK can be driven
with 1.8V to 3.3V logic.
CS (Pin 62): Serial Interface Chip Select Input. In serial
programming mode, (PAR/SER = 0V), CS is the serial in-
terface chip select input. When CS is low, SCK is enabled
for shifting data on SDI into the mode control registers.
In the parallel programming mode (PAR/SER = VDD), CS
controls the clock duty cycle stabilizer (see Table 2). CS
can be driven with 1.8V to 3.3V logic.
PAR/SER (Pin 63): Programming Mode Selection Pin.
Connect to ground to enable the serial programming mode
where CS, SCK, SDI, SDO become a serial interface that
control the A/D operating modes. Connect to VDD to en-
able the parallel programming mode where CS, SCK, SDI
become parallel logic inputs that control a reduced set of
the A/D operating modes. PAR/SER should be connected
directly to ground or the VDD of the part and not be driven
by a logic signal.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2155IUP-14#PBF | 2-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC64 |
| LTC2160CUK#TRPBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2160IUK#PBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2160IUK#TRPBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| LTC2162CUK#TRPBF | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2158-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:30MHz to 1.4GHz IQ Demodulator |
| LTC2158CUP-14 | 制造商:Linear Technology 功能描述:ADC DUAL 14BIT 310M 64QFN 制造商:Linear Technology 功能描述:ADC, DUAL, 14BIT, 310M, 64QFN |
| LTC2158CUP-14#PBF | 功能描述:IC ADC DUAL 14BIT 310M 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2158CUP-14#TRPBF | 功能描述:IC ADC DUAL 14BIT 310M 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯(lián) 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| LTC2158IUP-14 | 制造商:Linear Technology 功能描述:ADC DUAL 14BIT 310M 64QFN 制造商:Linear Technology 功能描述:ADC, DUAL, 14BIT, 310M, 64QFN |
發(fā)布緊急采購，3分鐘左右您將得到回復。