VDD
參數資料
型號： LTC2143IUP-14#TRPBF
廠商： Linear Technology
文件頁數： 6/38頁
文件大小： 0K
描述： IC ADC DUAL 14BIT 80 MSPS 64-QFN
標準包裝： 2,000
位數： 14
采樣率（每秒）： 80M
數據接口： 并聯，串行，SPI
轉換器數目： 2
功率耗散（最大）： 272mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-WFQFN 裸露焊盤
供應商設備封裝： 64-QFN（9x9）
包裝： 帶卷 (TR)
輸入數目和類型： 2 個差分
配用： DC890B-ND - BOARD USB DATA COLLECTION
LTC2145-14/
LTC2144-14/LTC2143-14
14
21454314fa
PINS THAT ARE THE SAME FOR ALL DIGITAL
OUTPUT MODES
VDD (Pins 1, 16, 17, 64): Analog Power Supply, 1.7V to
1.9V. Bypass to ground with 0.1μF ceramic capacitors.
Adjacent pins can share a bypass capacitor.
VCM1 (Pin 2):Common Mode Bias Output, Nominally Equal
to VDD/2. VCM1 should be used to bias the common mode
of the analog inputs to channel 1. Bypass to ground with
a 0.1μF ceramic capacitor.
GND (Pins 3, 6, 14): ADC Power Ground.
AIN1+ (Pin 4): Channel 1 Positive Differential Analog Input.
AIN1– (Pin 5): Channel 1 Negative Differential Analog Input.
REFH (Pins 7, 9): ADC High Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
REFL (Pins 8, 10): ADC Low Reference. See the Applica-
tions Information section for recommended bypassing
circuits for REFH and REFL.
PAR/SER (Pin 11): Programming Mode Selection Pin.
Connect to ground to enable the serial programming mode.
CS, SCK, SDI, SDO become a serial interface that control
the A/D operating modes. Connect to VDD to enable the
parallel programming mode where CS, SCK, SDI, SDO
become parallel logic inputs that control a reduced set of
the A/D operating modes. PAR/SER should be connected
directly to ground or VDD and not be driven by a logic signal.
AIN2+(Pin12):Channel2PositiveDifferentialAnalogInput.
AIN2–(Pin13):Channel2NegativeDifferentialAnalogInput.
VCM2 (Pin 15): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM2 should be used to bias the common
mode of the analog inputs to channel 2. Bypass to ground
with a 0.1μF ceramic capacitor.
ENC+ (Pin 18):
Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 19):
Encode Complement Input. Conversion
starts on the falling edge. Tie to GND for single-ended
encode mode.
CS (Pin 20): In Serial Programming Mode, (PAR/SER =
0V), CS Is the Serial Interface Chip Select Input. When
CS is low, SCK is enabled for shifting data on SDI into the
mode control registers. In the parallel programming mode
(PAR/SER = VDD),CScontrolstheclockdutycyclestabilizer
(See Table 2). CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 21): In Serial Programming Mode, (PAR/SER =
0V), SCK Is the Serial Interface Clock Input. In the parallel
programming mode (PAR/SER = VDD), SCK controls the
digital output mode (see Table 2). SCK can be driven with
1.8V to 3.3V logic.
SDI (Pin 22): In Serial Programming Mode, (PAR/SER =
0V), SDI Is the Serial Interface Data Input. Data on SDI
is clocked into the mode control registers on the rising
edge of SCK. In the parallel programming mode (PAR/
SER = VDD), SDI can be used together with SDO to power
down the part (see Table 2). SDI can be driven with 1.8V
to 3.3V logic.
OGND (Pin 41): Output Driver Ground. Must be shorted
to the ground plane by a very low inductance path. Use
multiple vias close to the pin.
OVDD (Pin 42): Output Driver Supply. Bypass to ground
with a 0.1μF ceramic capacitor.
SDO (Pin 61): In Serial Programming Mode, (PAR/SER
= 0V), SDO Is the Optional Serial Interface Data Output.
Data on SDO is read back from the mode control regis-
ters and can be latched on the falling edge of SCK. SDO
is an open-drain NMOS output that requires an external
2k pull-up resistor to 1.8V – 3.3V. If read back from the
mode control registers is not needed, the pull-up resistor
is not necessary and SDO can be left unconnected. In the
parallel programming mode (PAR/SER = VDD), SDO can
be used together with SDI to power down the part (see
Table 2). When used as an input, SDO can be driven with
1.8V to 3.3V logic through a 1k series resistor.
VREF (Pin 62): Reference Voltage Output. Bypass to
ground with a 2.2μF ceramic capacitor. The output voltage
is nominally 1.25V.
PIN FUNCTIONS
相關PDF資料
PDF描述
MS27474E14F35SD CONN RCPT 37POS JAM NUT W/SCKT
LTC2266IUJ-14#TRPBF IC ADC 14BIT 80MSPS DUAL 40QFN
IDT72V805L20PF8 IC FIFO SYNC 256X18 20NS 128QFP
MS27497E12A22S CONN RCPT 22POS WALL MNT W/SCKT
VI-B6P-MW-F1 CONVERTER MOD DC/DC 13.8V 100W
相關代理商/技術參數
參數描述
LTC2144-12 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 125Msps/105Msps/ 80Msps Low Power Dual ADCs
LTC2144-14 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 125Msps/105Msps/ 80Msps Low Power Dual ADCs
LTC2144CUP-12#PBF 功能描述:IC ADC DUAL 12BIT 105MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2144CUP-12#TRPBF 功能描述:IC ADC DUAL 12BIT 105MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2144CUP-14#PBF 功能描述:IC ADC DUAL 14BIT 105MSPS 64-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*