- 您現在的位置：買賣IC網 > PDF目錄5395 > LTC1992-5IMS8#TRPBF (Linear Technology)IC AMP/DVR I/O GAIN-5 DIFF 8MSOP PDF資料下載
參數資料
| 型號： | LTC1992-5IMS8#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 20/42頁 |
| 文件大小： | 0K |
| 描述： | IC AMP/DVR I/O GAIN-5 DIFF 8MSOP |
| 標準包裝： | 2,500 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 輸出類型： | 差分，滿擺幅 |
| 轉換速率： | 1.5 V/µs |
| 增益帶寬積： | 3.2MHz |
| 電流 - 輸入偏壓： | 2pA |
| 電壓 - 輸入偏移： | 250µV |
| 電流 - 電源： | 700µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±1.35 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC1992 Family
27
1992fb
APPLICATIONS INFORMATION
negative feedback and using an op amp’s differential input
to create the servo’s summing junction.
One servo controls the signal gain path. The differential
input of op amp A1 creates the summing junction of this
servo. Any voltage present at the input of A1 is amplified (by
the op amp’s large open-loop gain), sent to the summing
blocks and then onto the outputs. Taking note of the signs on
the summing blocks, op amp A1’s output moves +OUT and
–OUT in opposite directions. Applying a voltage step at
the INM node increases the +OUT voltage while the –OUT
voltage decreases. The RFB resistors connect the outputs
to the appropriate inputs establishing negative feedback and
closing the servo’s loop. Any servo loop always attempts
to drive its error voltage to zero. In this servo, the error
voltage is the voltage between the INM and INP nodes,
thus A1 will force the voltages on the INP and INM nodes
to be equal (within the part’s DC offset, open loop gain
and bandwidth limits). The “virtual short” between the
two inputs is conceptually the same as that for op amps
and is critical to understanding fully differential amplifier
applications.
The other servo controls the output common mode level.
The differential input of op amp A2 creates the summing
junction of this servo. Similar to the signal gain servo
above, any voltage present at the input of A2 is amplified,
sent to the summing blocks and then onto the outputs.
However, in this case, both outputs move in the same direc-
tion. The resistors RCMP and RCMM connect the +OUT and
–OUT outputs to A2’s inverting input establishing negative
feedback and closing the servo’s loop. The midpoint of
resistors RCMP and RCMM derives the output’s common
mode level (i.e., its average). This measure of the output’s
common mode level connects to A2’s inverting input while
A2’s noninverting input connects directly to the VOCM pin.
A2 forces the voltages on its inverting and noninverting
inputs to be equal. In other words, it forces the output
common mode voltage to be equal to the voltage on the
VOCM input pin.
For any fully differential amplifier application to function
properly both the signal gain servo and the common mode
level servo must be satisfied. When analyzing an applica-
tions circuit, the INP node voltage must equal the INM node
voltage and the output common mode voltage must equal
the VOCM voltage. If either of these servos is taken out of
the specified areas of operation (e.g., inputs taken beyond
the common mode range specifications, outputs hitting the
supply rails or input signals varying faster than the part
can track), the circuit will not function properly.
Fully Differential Amplifier Signal Conventions
Fully differential amplifiers have a multitude of signals and
signal ranges to consider. To maintain proper operation
with conventional op amps, the op amp’s inputs and its
output must not hit the supply rails and the input signal’s
common mode level must also be within the part’s speci-
fied limits. These considerations also apply to fully dif-
ferential amplifiers, but here there is an additional output
to consider and common mode level shifting complicates
matters. Figure 3 provides a list of the many signals and
specifications as well as the naming convention. The
phrase “common mode” appears in many places and often
leads to confusion. The fully differential amplifier’s ability
to uncouple input and output common mode levels yields
great design flexibility, but also complicates matters some.
For simplicity, the equations in Figure 3 also assume an
ideal amplifier and perfect resistor matching. For a detailed
analysis, consult the fully differential amplifier applications
circuit analysis section.
Basic Applications Circuits
Most fully differential amplifier applications circuits employ
symmetrical feedback networks and are familiar territory
for op amp users. Symmetrical feedback networks require
that the –VIN/+VOUT network is a mirror image duplicate of
the +VIN/–VOUT network. Each of these half circuits is basi-
cally just a standard inverting gain op amp circuit. Figure 4
shows three basic inverting gain op amp circuits and their
corresponding fully differential amplifier cousins. The vast
majority of fully differential amplifier circuits derive from
old tried and true inverting op amp circuits. To create a
fully differential amplifier circuit from an inverting op amp
circuit, first simply transfer the op amp’s VIN/VOUT network
to the fully differential amplifier’s –VIN/+VOUT nodes. Then,
take a mirror image duplicate of the network and apply it
to the fully differential amplifier’s +VIN/–VOUT nodes. Op
amp users can comfortably transfer any inverting op amp
circuit to a fully differential amplifier in this manner.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1783CS6#TR | IC OPAMP R-R I/O MICRPWR SOT23-6 |
| SA17CA | TVS BIDIRECT 500W 17V DO-15 |
| LT1114IS#TRPBF | IC OP AMP PREC LOPWR QUAD 16SOIC |
| LTC6912IDE-1#TRPBF | IC PGA DIGITAL R-R DUAL 12-DFN |
| SA6V5CA | TVS BIDIRECT 500W 6.5V DO-15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1992CMS8 | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992CMS8#PBF | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LTC1992CMS8#TR | 功能描述:IC AMP DIFF I/O ADJ OUT 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992CMS8#TRPBF | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992HMS8 | 功能描述:IC AMP DIFF I/O ADJ OUT 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
發布緊急采購，3分鐘左右您將得到回復。